Easy
15-30 minutes
This is a genuine OEM sourced replacement part which is specially designed for use with Homelite generators. The purpose of a carburetor is to mix the air and the gas before the combustible mix goes to the engine. Over time components may wear out and begin to fail eventually requiring a replacement to maintain peak performance. Keep in mind this high-quality metal body carburetor is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part.
Carburetor Assembly 16100-Z191110
OEM part for: Homelite
Part Number: 16100-Z191110
$72.18
In Stock
Ships within 1 business day 
Jump To:
Frequently Purchased Together ?
Compatibility
This part will fit the following 2 machines
Homelite
PS905000 5,000 Watt Generator View Diagrams & Manuals
PS906025 6,000 Watt Generator View Diagrams & Manuals
This item works with the following types of products:
- Generator Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Carburetor Assembly
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Carb contaminated from old fuel
Andy - March 6, 2018
👍 1 of 1 people found this instruction helpful
Tool Type
Generator
Difficulty
Easy
Time
15-30 minutes
Tools Used
Pliers, Socket set
Parts Used
Removed air filter assembly
Removed throttle linkage and spring from throttle shaft, removed fuel supply line
Removed carburetor
Reassembled in reverse order
Replaced fuel filter
Put fuel in tank
Checked operation of unit.
Removed throttle linkage and spring from throttle shaft, removed fuel supply line
Removed carburetor
Reassembled in reverse order
Replaced fuel filter
Put fuel in tank
Checked operation of unit.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Carburetor was clogged
Francis - July 26, 2017
👍 1 of 1 people found this instruction helpful
Tool Type
Generator
Difficulty
Easy
Time
15-30 minutes
Tools Used
Pliers, Nutdriver
Parts Used
Disconnected spring and rod for air flapper. Took off and replaced carburetor, replaced spring etc, let bowl fill up. Started on 1st pull.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Generator wouldn't start
Gary - October 24, 2017
Tool Type
Generator
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Nutdriver
1. Confirmed that gas filter wasn't clogged.
2. Confirmed that generator did operate by spraying carburetor cleaner (high octane fuel in a spray can) directly into the carburetor (with air filter removed) and pulling the starter rope.
3. Ordered new carburetor assembly with gasket.
4. When new carburetor arrived, removed the old carburetor by (a) turning off the gas feed line, (b) pulling the gas feed line off the carburetor, (c) puling off other tubes, and (d) removing the two nuts that connect the carburetor to the engine.
5. Peeled off the old carburetor gasket.
6. Installed new gasket and carburetor and reconnected gas line, other tubes and air filter.
7. Turned the gas feed line back on and pulled starter rope to start the generator.
2. Confirmed that generator did operate by spraying carburetor cleaner (high octane fuel in a spray can) directly into the carburetor (with air filter removed) and pulling the starter rope.
3. Ordered new carburetor assembly with gasket.
4. When new carburetor arrived, removed the old carburetor by (a) turning off the gas feed line, (b) pulling the gas feed line off the carburetor, (c) puling off other tubes, and (d) removing the two nuts that connect the carburetor to the engine.
5. Peeled off the old carburetor gasket.
6. Installed new gasket and carburetor and reconnected gas line, other tubes and air filter.
7. Turned the gas feed line back on and pulled starter rope to start the generator.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Would not start
Fred - March 25, 2017
Tool Type
Generator
Difficulty
Medium
Time
15-30 minutes
Tools Used
Pliers, Socket set, Wrench Set, Nutdriver
Parts Used
Removed air filter, linkage to throttle, gas lines and emission tube. Removed old carb, installed new. Replaced the pieces removed let it sit for enough time to fill the carb bowl with fuel and the generator started second pull!
Before ordering I worked on it for 2-3 hours! Should have saved the time and just waited for the new part!
Before ordering I worked on it for 2-3 hours! Should have saved the time and just waited for the new part!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Replace carburetor
Izet - April 30, 2016
👍 1 of 2 people found this instruction helpful
Tool Type
Generator
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Pliers, Wrench Set
Parts Used
Remove air filter over. Remove 2 nuts!!! One in the air intake one outside the unit. Simply slide off the air filter housing. Then you see the carburetor. Simply slides off 2 long welded bolts. And before you do that remove spring from top of carburetor. And the carb.. Sliders of keep all seals and gaskets. Transfer to new unit. Reverse your steps and your back in action!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
