Easy
15-30 minutes
Auto On-off Pcb 120v - Xc W107406161
OEM part for: Makita
Part Number: W107406161
$212.35
In Stock
Order within the next 7 hours and your part ships today! 
Compatibility
This part will fit the following 1 machine
Makita
VC4710 12 Gallon Wet/Dry Vacuum View Diagrams & Manuals
This item works with the following types of products:
- Vacuum Parts
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Auto On-off Pcb 120v - Xc
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Switch/knob to activate the vacuum stopped working.
Michael - February 21, 2024
Tool Type
Vacuum
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Torxs bits required on the makita shop vac disassembly
Parts Used
Pretty simple repair. Remove the top of the vacuum using two different size torx bits. Take photos or remove the wires and tubes one at a time and transfer them to the new board/switch. Knob is held on with a flat head set screw. Reassemble being careful to route wires so they aren’t pinched.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Vacuum wouldn't start. I believe the switch was bad but you can't get just the switch. you have to replace the whole circuit board.
Michael - July 27, 2020
Tool Type
Vacuum
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, torx bits
Parts Used
Remove the top cover of vac by removing a handful of torx screws to expose the motor and circuit board and then swap out the circuit board connections one by one.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
The timer switch was bad
Don - September 14, 2018
Tool Type
Vacuum
Difficulty
Easy
Time
30-60 minutes
Tools Used
Pliers, Torx set
Parts Used
Removed the outer cover. Removed mounting screws from the printed circuit board. Removed electrical wiring one wire at a time and installed that wire in the same location on the new printed circuit . Next move the 2 vacuum hoses from the board to the same locations on the new board. Install the new board and outer cover. Check operation of vacuum.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
