This genuine Char-Broil replacement flame tamer is designed to help your grill perform at its best. Sold individually, this part serves two important functions: it evenly diffuses heat from the burners below to ensure consistent cooking, and it acts as a barrier to prevent grease and food particles from clogging or damaging the burners.
Made from durable materials and built to match original specifications, this flame tamer helps extend the life of your grill while improving heat distribution and reducing flare-ups. Whether you're replacing a worn part or upgrading your grill’s performance, this OEM component is a smart and simple solution.
Troubleshooting
This part works with the following brands:
Char-Broil
This part works with the following products:
Grill
Part# 80029723 replaces these:
80003332, 80015759, 80016301, G501-0008-W1,
★
Customer Part Reviews
?
4.9
Average Rating (out of 5):
★★★★★
★★★★★
(27 Reviews)
Click to filter by ratings:
5 stars
26
4 stars
0
3 stars
0
2 stars
0
1 star
1
< Prev
1
2
3
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
GREAT product. Works perfectly. Will definitely order again. A++++++++
Received in new condition. Exactly as I ordered. I will definitely bookmark this and be ordering again real soon. Thank you. GREAT job.
Randy - August 20, 2019
Verified Purchase
★★★★★
★★★★★
Easy and Fast
I had an old rusted BBQ grill needing upgrade replacement parts. These parts were easily found, ordered and received. Can't get any easier that. Good Job!
Carl - October 21, 2019
Verified Purchase
★★★★★
★★★★★
easy replacement
just slipped right in. great
Guest - June 18, 2020
Verified Purchase
★★★★★
★★★★★
Replaced part took 10 seconds
New part great condition.
Guest - June 15, 2020
Verified Purchase
★★★★★
★★★★★
Easy replacement!
Even during delays caused by the pandemic, my order was shipped with little delay. The parts fit perfectly and were packed very well for shipment.
Guest - June 22, 2020
Verified Purchase
★★★★★
★★★★★
worked great.
arrived quickly and fit great
Guest - August 25, 2020
Verified Purchase
★★★★★
★★★★★
I was impressed to find parts for an older unit of 13 years!
Having the exploded diagram of parts for my model unit made it super easy to identify the parts I needed. They arrived in less than a week. The parts were and exact fit. The performance of the grill was returned to its original intensity. I will keep this company in mind for future repairs. 5/5 Sam
Guest - September 15, 2020
Verified Purchase
★★★★★
★★★★★
Parts as needed
Identified correct parts for grill and order arrived promptly.
Guest - January 28, 2021
Verified Purchase
★★★★★
★★★★★
Easy
Arrived a lot faster than I thought it would.
Guest - June 18, 2021
Verified Purchase
★★★★★
★★★★★
Barbeque replacement grids
Item as described. Happy to be able to continue use.
Guest - July 27, 2021
Verified Purchase
< Prev
1
2
3
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
The most difficult part was removing the old rusted out parts and screws. The screws were corroded so bad it was there wasn\'t really a place to insert the screwdriver. Using rust remover/ bolt loosener and needle nosed pliers, work solution down into screw grooves until screw spins freely. Remove screws but save them. Not all of the new
... Read morescrews fit in the existing holes. Be sure to remove the screws that attach the igniter from the igniter burner before trying to pull out the igniter burner (there are 2). After screws are removed parts easily pull out or lift off. New parts were not an exact fit but we\'re better quality and we\'re close enough to make it work. Attach the igniter back onto the new igniter burner before trying to attach anything else (reuse of old screw school was necessary here). Lay in all burners and carry over tubes, insert screws but do not tighten all the way. After everything aligns tighten each screw most but not all of the way. Then go back and tighten them all the way. Other wise it is difficult to align the last screw. Also, be sure all of the carry over tubes face the same and correct direction.
1. Removed flame tamer bars and discarded. No tools necessary
2. Removed crossover tubes. Screws were rusted. Used vice grip pliers on the head of screws to back them out. Burners were in good shape and did not needed to be replaced.
3. Parts were a perfect fit. Replacement cross over tubes were a perfect fit and came with new
... Read more screws. No problems to install.
4. Flame tamer bars were drop in replacements.
5. Grill is ready for another 1000 burgers.
I removed cooking grates from grill then slid old flame tamers out with just the hands, no tools required for this. Slid replacement flame tamers and replaced cooking grates. That\'s it, ready to grill again!
Our barbecue hasn\'t worked for a while. I was reluctant to buy a new one, and decided to take the plunge and see if it were worth trying to rebuild the Char-Broil I had (now close to 10 years old). So I did the following:
1. Removed old parts.
2. Cleaned unit.
3. Got online and ordered new parts.
4. When pa
... Read morerts arrived, got frustrated that I had ordered the wrong ones (hadn\'t checked the serial number).
5. Called eReplacement, who helped me figure out the right ones and facilitated the return.
6. Sulked.
7. New parts arrived and were installed within about 25 minutes.
8. Barbecued chicken and corn for dinner.
9. Did the happy dance!
Replaced the tamers and burners. The burner screws needed some liquid wrench. But I did remove them. Part of the front support for the tamers were rotted so I put a few screws in to provide a stud for the tamers to \'perch\' on.
The parts were very easy to find on your site and were delivered 2 to 3 days earlier than the projected delivery date. All the parts were replaced in under 15 minutes using only phillips screwdriver and was back to grilling. I highly recommend using this site for you\'re parts.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
