This is a genuine Char-Broil replacement part, it is sold individually. Carryover tubes connect the gas grill burners and carry the flame from one burner to the next. Over time, your carryover tubes may rust or warp. This would be the time to replace them.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Easy to install
Parts fit great and grill up and running
Guest - June 6, 2019
Verified Purchase
★★★★★
★★★★★
Perfect fit. My grill is now like new.
I found the entire process of ordering the parts to refurbish my grill very efficient at eReplacementParts. I just entered my model number, and the website showed me the exploded view of my entire grill. It was so easy and accurate that I ordered some parts that were ok, but would need to be replaced in the next couple years so I could do it all at one time. Hardest part was removing the old screws. Thanks so much.
Oliver - August 20, 2019
Verified Purchase
★★★★★
★★★★★
Grill Parts
My grill is all better, Thanks!
Guest - April 4, 2020
Verified Purchase
★★★★★
★★★★★
Excellent
Price and service were great! I would go back in a minute for parts etc.
Guest - September 16, 2020
Verified Purchase
★★★★★
★★★★★
Gas crossover repaired
These parts were the perfect fit fir my older charbroil bbq
Guest - July 20, 2021
Verified Purchase
★★★★★
★★★★★
Perfect fit
Works perfect
Guest - February 26, 2022
Verified Purchase
★★★★★
★★★★★
Works like new
My tubes were corroded and leaking flame. These are great replacements. The screws are loose because of general decay in the burner tubes, but they work with some bending of the new carry over tubes.
Brett - April 26, 2023
Verified Purchase
★★★★★
★★★★★
Flame tube.
This part was not the exact same size, but did fit and function well.
My model number would not match any available options given.
I'm fine with how this worked out.
Guest - October 20, 2021
Verified Purchase
★★★★★
★★★★★
disappointed
The parts that came did not fit the grill model I ordered,
I compared them with the broken parts and they are completely different
Iglobal - May 26, 2020
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1 I removed the main burner tubes and distribution tubes. I use a screwdriver and socket set.
2 I fitted the new burner tubes in place
3 Screwed the distribution tubes in place
4 Place the tents in their slots
5 Turned on the gas
I used a wire brush to clean up the heads of some of the screwdriver slots on the old rusted parts. Some of the old round-headed bolts with nuts broke when trying to take them out. This was ok because there are more than enough new bolts, nuts, washers, lock washers and screws supplied with the new original replacement parts to do the job
... Read more even if you drop and lose a few. I used never seize on all the new bolts and screw threads when installing for ease of future parts replacement. I replaced all 5 main burners, 4 carryover tubes, 5 heat tents and one searing burner. All original replacement parts installed easily and fit exactly where they were designed to. I used the old electrodes and had to adjust the distance a little to get a good spark to ignite the gas properly. I ran all the burners wide open for 20 minutes and then let it cool down before cooking on the grill.
All the screws were rust and corroded. I had to drill them out, replaced with stainless steel screws. Simple to change out the burner and carry over tubes then. For the heat tent just remove the old rusted ones and place the new ones in by hand.
I took the cooking grates off and took them to the car wash and power washed them. (Quick and easy clean for a dollar). I took out the rusty heat tents and then just like everyone else on here, the screws that hold the burners in place wouldn\'t come out. The heads twisted off or they just stripped out. Instead of drilling them out, I use
... Read mored an angle grinder with a cut-off wheel to buzz the heads off the screws and then the whole burner assembly came right out. The burners I ordered came with all the necessary screws, washers, and nuts. The only thing I had to mess with was the igniters. I had to drill out the holes for the igniter on the sear burner and reattach it to the new one. My grill looks brand new now and I\'m very happy with it.
Remove grill grates to access heat tents
Removed them then used screw driver to remove .carry over tubes.
Gave grill a good cleaning
Then installed new tubes and tents
For $65 total my $300 grill is new again.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Grill","title":"Grill","url":"/parts/bbq/grill/"},{"position":2,"name":"Hose or Tube","title":"Hose or Tube","url":"/parts/bbq/grill/hoses-and-tubes/"},{"position":3,"name":"G651-L902-W2","title":"G651-L902-W2","url":""}]
