866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Makita Parts  Makita Drill Washers

Makita Drill Washers

Flat Washer
Part Number: 253804-1
In Stock, 25+ available
Genuine Makita replacement part, it is sold individually.
This washer is used in various areas in the tool model numbers shown below.
It is used as a washer for a screw or bolt or even as a spacer.
Flat Washer
Part Number: 267085-1
In Stock, 25+ available
This is a Genuine OEM Sourced replacement part designed for Makita Impact Drivers. This part is made out of Metal and it is Sold Individually. This Washer helps to provide seal for the Sleeve.

When replacing this part you would need a Screwdriver and Pliers.
Flat Washer 6
Part Number: 941152-7
In Stock, 4 available
This is an authentic manufacturer sourced replacement part. It is commonly used on a variety of Makita power tools. It is used to distribute the pressure evenly between two connected parts. Since this washer is a standard hardware that has multiple applications, it is recommend to check appropriate diagrams for correct location and use of it. This part is made out of metal and it is sold individually.
Spring Washer 6
Part Number: 942151-2
In Stock, 25+ available
This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out of metal and no tools should be necessary when replacing this item. This is an OEM Makita part directly sourced from the manufacturer for use with saws, cutters, planers, drills, and trimmers.
Flat Washer 12
Part Number: 253052-2
In Stock, 15 available
It is a genuine OEM supplied replacement flat washer which has a few different applications depending on the tool, make sure to check appropriate diagrams for correct location and use of this hardware. Please note this part is made from high quality metal and it is sold individually.
Flat Washer 8
Part Number: 941202-8
In Stock, 11 available
It is an authentic item which is supplied by the original equipment manufacturer for use with Makita power tools. The purpose of this flat washer is to provide a tight seal between connected parts, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable part is made of high-quality metal and is sold individually.
Insulation Washer
Part Number: 681636-0
In Stock, 12 available
Included in part number 515616-3
Flat Washer 6
Part Number: 253715-0
In Stock, 8 available
It is a genuine item which is supplied directly from the original equipment manufacturer for use with Makita saws. The purpose of this flat washer is to provide a tight seal between connected parts, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable part is made of high-quality metal and is sold individually.
Flat Washer 16
Part Number: 253707-9
In Stock, 3 available
This authentic flat washer is a high quality item that is sourced from original equipment manufacturer for use with Makita power tools. Its purpose is to distribute the pressure evenly between the two connected parts. It has multiple applications depending on your unit, please make sure to check appropriate diagrams for correct location and use of this item. One durable metal flat washer is included per order.
Wave Washer 10
Part Number: 253932-2
In Stock, 13 available
This is an authentic replacement part manufactured for use with Makita miter saws, drills, and planers. Wave washers are commonly used to provide spacing between parts and to deflect pressure between parts. The wave washer is sold individually.
Hex. Washer
Part Number: 345280-4
In Stock, 8 available
This hex washer is an OEM part direct from Makita. The metal washer helps the hex bolt to secure the grip base and handle. This item is sold individually, and a wrench is required for the proper installation.
Insulation Washer
Part Number: 681614-0
In Stock, 12 available
This genuine manufacturer-sourced part is specially designed for Makita power tools. It is an important component which provides a tight seal between connected components. Unfortunately, over time it will wear out and it may begin to crack eventually requiring a replacement. To ensure the correct repair procedure, refer to the appropriate diagrams for your model. Note, this high-quality insulation washer is made of durable material and is sold as an individual item. A screwdriver will be needed to take apart and reassemble the tool when performing this repair.
Nylon Washer 14
Part Number: 261108-7
In Stock, 10 available
This is a genuine Makita replacement part used in compatible impact drivers and impact wrenches. The nylon washer fits between the hammer case and the anvil and is made of plastic. You may need a screwdriver when replacing this item. It may become broken and will need to be replaced. This item is available as an individual replacement part.
Flat Washer 15
Part Number: 267164-5
Ships in 6 - 12 business days
Flat Washer 10
Part Number: 253180-3
Ships in 6 - 12 business days
Flat Washer 8
Part Number: 253139-0
In Stock, 2 available
This is an original Makita part for use in saws, drills, nibblers, planers, polishers, sanders, and shears. The flat washer goes between the gear shaft and the needle bearing. During the installation process, an allen wrench and a set of pliers might be needed to replace this part. It will need to be replaced if it becomes broken. This is made of metal and is sold individually.
Insulation Washer
Part Number: 681613-2
In Stock, 4 available
This is a genuine replacement part which is supplied directly from the original equipment manufacturer. The plastic insulation washer sits between the ball bearing and the armature assembly. This part is used on nibblers, shears, planers, jig saws, masonry saws and circular saws to disperse heat as well as insulate the surrounding components. This part is sold individually.
Flat Washer 12
Part Number: 253744-3
Ships in 6 - 12 business days
This is a genuine Makita part sourced directly from the manufacturer for use in drills, grinders, impact drivers, impact wrenches, jointers, saws, planers, rotary hammers, sanders, and shears. The flat washer goes next to the vice plate and is made of metal. A screwdriver may be necessary during the installation of this item. It may become broken and will need to be replaced. This is available as an individual replacement part.
Flat Washer 5
Part Number: 253807-5
In Stock, 3 available
Flat Washer 13
Part Number: 253798-0
In Stock, 2 available
A genuine item which is supplied directly from the original equipment manufacturer for use with Makita power tools. A washer helps to distribute pressure and provide a tight seal between connected parts, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable metal and is sold individually.
Show More
no image
Part Number:
visa mastercard discover american express PayPal
HACKER SAFE certified sites prevent over 99.9% of hacker crime.

fancyboxy