Black and Decker Electric Drill Parts
We sell only genuine OEM Black and Decker ® parts.
Top Black and Decker Electric Drill Models
-
Black and Decker 110 (Type 1) Spade Handle Drill Electric Drill Parts
-
Black and Decker 9020 (Type 5) 3/8 Reversible Drill & Screwdriver Electric Drill Parts
-
Black and Decker 9020 (Type 1) 3/8 Reversible Drill & Screwdriver Electric Drill Parts
-
Black and Decker 9020 (Type 4) 3/8 Reversible Drill & Screwdriver Electric Drill Parts
-
Black and Decker 9020 (Type 2) 3/8 Reversible Drill & Screwdriver Electric Drill Parts
-
Black and Decker 9020 (Type 6) 3/8 Reversible Drill & Screwdriver Electric Drill Parts
-
Black and Decker 9020 (Type 3) 3/8 Reversible Drill & Screwdriver Electric Drill Parts
-
Black and Decker 1065 (Type 3) 1/4 Drill 120 Volt Electric Drill Parts
Popular Black and Decker Electric Drill Parts
- Manufacturer Part Number:
- 450374-12
Genuine OEM replacement This brush is sold individually, 2 are needed for most every electric power tool It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the...
- Manufacturer Part Number:
- 429634-00
This is an authentic manufacturer approved replacement part designed for use with drills/screwdrivers. This clutch assembly is connected to the transmission and the shaft. Keeping an eye on equipment performance will determine when the clutch requires replacement. Includes part numbers 176842-00, 89210-00
- Manufacturer Part Number:
- 90593303-01
This is a genuine Black and Decker replacement charger, sold individually. It’s designed to recharge the battery used in the cordless tools listed below. Over time, chargers can wear out or stop functioning properly. Replacing the charger is a cost-effective solution that can extend the life of your tools—often much less expensive than purchasing a brand-new unit.
- Manufacturer Part Number:
- 176846-04
This carbon brush is an authentic DeWalt replacement part. It is sold individually, 2 are needed to make a set • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that c...
- Manufacturer Part Number:
- 400814-00
Genuine Dewalt/Black & Decker replacement part. includes 1 Carbon Brush with wire lead and brush spring attached. 2 Brushes are needed for the tools listed below. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power...
- Manufacturer Part Number:
- 628037-00
This is an original replacement part manufactured for use with drills. This hardened plastic spade handle is secured at the back of the drill using a knob, which is available separately. The spade handle provides an additional grip option for heavy duty drills, please note the spade handle is sold individually.
- Manufacturer Part Number:
- 445860-00
This is a genuine OEM replacement part, it is sold individually. This part is used to keep the brush tight against the armature so the tool will work properly. Over time when the brushes wear down and heat is created, the spring may lose its tension and will have to be replaced.
- Manufacturer Part Number:
- 90640340
Genuine Manufacturer Sourced replacement part used on some Black and Decker Power Tools. This item is sold individually. Purchasing a charger will be less expensive than buying a new tool. Please note that a weak or defective battery can damage the charger. Weak batteries are batteries with bad cells. These type of batteries will not hold a charge. It will send a message to the charger to keep cha...
- Manufacturer Part Number:
- 330005-01
- Manufacturer Part Number:
- 605040-15
Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.
- Manufacturer Part Number:
- 330072-98
Length: 8'
Gauge: 18
Wires: 2
Type: Bare Wire
This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also rou...
- Manufacturer Part Number:
- 445338-00
This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
Black and Decker Electric Drill Models
-
Black and Decker 110 (Type 1) Spade Handle Drill Electric Drill
-
Black and Decker 9020 (Type 5) 3/8 Reversible Drill & Screwdriver Electric Drill
-
Black and Decker 9020 (Type 1) 3/8 Reversible Drill & Screwdriver Electric Drill
-
Black and Decker 9020 (Type 4) 3/8 Reversible Drill & Screwdriver Electric Drill
-
Black and Decker 9020 (Type 2) 3/8 Reversible Drill & Screwdriver Electric Drill
-
Black and Decker 9020 (Type 6) 3/8 Reversible Drill & Screwdriver Electric Drill
-
Black and Decker 9020 (Type 3) 3/8 Reversible Drill & Screwdriver Electric Drill
-
Black and Decker 1065 (Type 3) 1/4 Drill 120 Volt Electric Drill
-
Black and Decker 1065 (Type 100) 1/4 Drill 120 Volt Electric Drill
-
Black and Decker 1575 (Type 101) 3/8 Reversible Variable Speed Drill 120 Electric Drill
-
Black and Decker 11228 (Type 1) 7.2V Drill Electric Drill
-
Black and Decker 288 (Type 101) Versa Clutch Scrugun Electric Drill
-
Black and Decker 288 (Type 100) Versa Clutch Scrugun Electric Drill
-
Black and Decker 288 (Type 102) Versa Clutch Scrugun Electric Drill
-
Black and Decker 1330 (Type 4) 5/8 Sdr Drill 450 Rpm Electric Drill
-
Black and Decker 1321 (Type 1) 1/2" Heavy Duty Reversing Drill Electric Drill
-
Black and Decker 1321 (Type 3) 1/2" Heavy Duty Reversing Drill Electric Drill
-
Black and Decker 1321 (Type 2) 1/2" Heavy Duty Reversing Drill Electric Drill
-
Black and Decker 1321 (Type 5) 1/2" Extra Heavy Duty Reversing Drill Electric Drill
-
Black and Decker 1321 (Type 6) 1/2 Hd Drill 120 Volt Electric Drill