866-322-9842
Mon-Fri 7am-1am EST
Sat-Sun 7am-11pm EST
Repair Parts Home  Power Tool Parts  DeWALT Parts  5140011-85 Carbon Brush With Spring

Carbon Brush With Spring

Part Number: 5140011-85
DeWALTBlack and DeckerDelta
Availability: 25+ in stock
Price: $8.78
Quantity:
Ships within 1 business day

*This part replaces obsolete part #: and 286032-00.

Description:
This is an authentic OEM replacement part. Sold individually.

Carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Because of this, carbon brushes are one of the most commonly replaced power tool parts.

A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

This part is compatible with the models listed below.
Product Information
Manufacturer: DeWALT, Black and Decker, Delta
Product Number: 5140011-85
Classification: Part
Weight: 0.01 lbs.
Also Known As: Motor Brush With Spring
Shipping: Ships Worldwide
Repair Guides
Watch the Repair Video for Carbon Brush With Spring
How to Replace the Motor Brushes on a DeWALT Planer
Articles:
How to Replace the Motor Brushes on a DeWALT Planer
Step-by-step instructions for removing and installing the motor brushes on your DeWALT planer....
December 12, 2017
Products Compatibility

This item works with the following types of products:

  • • Planer
  • • Saw
  • • Table Saw
  • • Trim Saw
Questions & Answers

No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
6 of 6 people found this instruction helpful
Tool Type:
Planer
Parts Used:
Carbon Brush With Spring - 5140011-85
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, spring hook
Motor quit in middle of planing a board. Would noy restart
Check power input from source all the way to the on/off switch and then to the motor cord itself. If present to motor, then pop out the brushes and check them. If worn or no spring tension remaining, replace and unit will run like new. Using a screwdriver, remove the brush caps, remove the worn brushes, then install the new brushes, then screw the brush caps back on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Planer
Parts Used:
Carbon Brush With Spring - 5140011-85
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Brushes were worn
Removed the brush caps, removed the old brushes, installed the new brushes, installed the brush caps
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Planer
Parts Used:
Carbon Brush With Spring - 5140011-85
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Worn brushes
With a screwdriver remove the brush caps. Then, removed the worn brushes and blow out the motor with compressed air. Install the new brushes. Then screw the brush caps back on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
2 of 2 people found this instruction helpful
Tool Type:
Planer
Parts Used:
Carbon Brush With Spring - 5140011-85
Circuit Breaker - 5140000-19
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, electrical tester
Planer does not run.
Took most of the time to figure out how to disassemble the motor from the frame. Came up with very difficult. Last thing was to remove on/off switch... surprise! Access to circuit breaker via cavity behind switch. Breaker showed about 11 ohms, should have been zero. Tried a bypass, motor came on instantly, This breaker has been tripped MANY times. I've used the planer for hundreds of hours.

Went online to find ereplacement parts during my first investigation (drawings), and then to order parts after problem solved. The brushes were ok, but I figured order now, to use later.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Planer
Parts Used:
Carbon Brush With Spring - 5140011-85
Brush Holder - 5140011-86
Brush Cap - 5140011-84
Repair Difficulty:
Medium
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Assorted allen wrenches
Planer did not work, one brush holder threads were stripped
Removed the brush caps
Remove the old worn brushes
Loosened the set screws securing the brush holders, and removed the brush holders
Place the new brush holders in place and tightened the set screws
Installed the new brushes
Screwed the new brush caps in
Did you find this story helpful?
Thanks for voting and helping fellow customers!
1 of 1 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Carbon Brush With Spring - 5140011-85
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Worn out brushes
I removed the brush cap on the motor assembly with a screwdriver, Then I pulled the brushes out of the brush holder. Blow out the and clean the brush holder so that the new brushes will slide in easily and make good contact with the armature. Inserted the brushes in the brush holder and screw the brush caps back on. They were perfect and easy. Will buy again. AAAAAA+++++++++
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Circular Saw
Parts Used:
Carbon Brush - 176846-04
Carbon Brush With Spring - 5140011-85
Tension Spring 4 - 231839-2
Carbon Brush With Spring - 450374-12
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Old and worn out
On the saws just removed the blades and clipped the springs in place. Replacing the brushes only took removing the caps.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Planer
Parts Used:
Carbon Brush With Spring - 5140011-85
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Worn out brushes
1. Removed the screw cap that holds the brushes in and pulled the old brushes.
2. Discovered that the "oem" parts (i.e. carbon brushes) were a different size than the originals.
3. I was able to insert the incorrect size brushes and make the machine work until I can find a company that carries a correct size Carbon brush with spring.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Planer
Parts Used:
Carbon Brush With Spring - 5140011-85
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Wouldn't start
Followed the recommended fix of installing new brushes.
Watched the U tube video
Everything fit perfectly, installed easily and the machine is up and running again.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Planer
Parts Used:
Carbon Brush With Spring - 5140011-85
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Brushes arcing pretty heavily
Installed the new brushes, stopped the arcing
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Discussion
Discussion for Carbon Brush With Spring - ( 5140011-85 )
Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
Question: How To Replace Motor Brushes ?

greg607

Need to know how to replace motor brushes on delta 33-050 type 1 trim saw, this model has electric blade brake.
Hi greg,
That should be pretty straight link removed a screw driver to remove the two black brush caps on the side of the motor.Then carefully pull out the brush and spring link removed the new ones in reverse order.Hope that helps.Good luck.
Tinker
HI Tinker,
Thanks for getting back with me on the instructions for changing motor brushes.
Tinker, my saw has the automatic electric blade brake, I tried to gently pull the
brush out but it will not come out and knowing me, I'll brake it!
I think the electric brake is keeping it from coming out, I don't know.
What do you think?
Greg
HI Tinker,
Thanks for getting back with me on the instructions for changing motor brushes.
Tinker, my saw has the automatic electric blade brake, I tried to gently pull the
brush out but it will not come out and knowing me, I'll brake it!
I think the electric brake is keeping it from coming out, I don't know.
What do you think?
Greg
Hi Greg,
Generally ,If the brushes are frozen in the brush tubes it indicates that the tool has over heated wrapping the brush tubes.The brake is an electrical effect that takes place when the tool is shut off momentarily throwing the motor in to reverse for a second or two.It has no effect on the brushes.Some times you can reach in and pull the brushes out with a pliers or in some cases the case will have to be removed and the brushes driven out . When replacing the brushes if they are a tight fit going in you can sand the a slight amount to get them to fit right.Hope that helps.
Good luck.
Tinker
Hi Tinker,
Thanks for getting back with me. I'll give it a try and hope it works out ok.
I have worked on a lot of tools and just about everything else, but sometimes
it helps to get some advise. Thanks for the advice!
Greg
Reviews
5
Average Rating (out of 5):
1 Reviews
Click to filter by ratings:
5 stars
1
4 stars
0
3 stars
0
2 stars
0
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
NEXT >
  • Service
    It was a compatible part to an old tool that I thought I would never be able to use again. That's great!!! Thanks
    Guest - April 30, 2019 Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    visa mastercard discover american express PayPal
    HACKER SAFE certified sites prevent over 99.9% of hacker crime.

    fancyboxy