I replaced the fuel line/filter first. Removing the old filter was a chore because of the tight fit of the barbs on the filter. Pushing it out with the pliers, little by little, worked well. The new fuel line/filter did not fit well into the hole, so i used a drill bit of the same size as the hole & carefully reamed out the inside of the
... Read morehole by hand (the plastic fuel tank) so i could get it started through the hole. Tight working space. I used a flat screwdriver to push the filter down into place - inserted through the fuel tank opening - as well as gently pulling on the line & took some work to get it fully seated.
Replacing the air cleaner filter and spark plug were simple and quick. There were 4 torx head screws to remove the cover. The screws also have a slot for a straight-blade screwdriver, but it was worth it to get the Torx set.
Replacing the auto feed line assembly was straightforward, except there is a somewhat hidden setscrew on the inside of the shaft that must be removed. No replacement instructions came with the assembly, so I struggled with removing the old one before finding the setscrew. Once I removed it, the assembly removal and replacement was quick and easy.
The trimmer starts, runs, and doesn\'t leak.
Read less
Did you find this story helpful?
Thank you for voting!
Ryopbi weed trimmer had not been used for 5 years and wouldnÆt start.
I had a Ryobi weed trimmer that i took to two shops for a tune and replace old fuel lines...both shops recommended i buy a new one as the cost of repairing the item was going to likely run $90-$120 and it was pointed out to me that i could buy a new one for $120...after figuring what parts i needed it cost under $50 and my time (1 hour).
... Read more
Watched a YouTube video on replacing fuel lines and general tune up...looked up my brand/model on ereplacementParts.com and they had all the parts listed for any repair i might have...i selected the parts mentioned in the video and paid for them in the easy check out... they were delivered within a couple days...I watched the video again and re-assembled my parts and the trimmer started right up...the next day i was trimming about an acre of weeds n grass..
This was my first time using ereplacementParts.com. For me everything went great..i highly recommend them to anyone trying to repair your own equipment...
Read less
Did you find this story helpful?
Thank you for voting!
Replace fuel filter in tank, replace plug and install new air filter.
I REMOVED THE SCREWS TO THE FRONT OF THE MOTOR ND THE COVERS TO THE REAR OF THE MOTOR TO EXPOSE THE HOSES AND SPARK PLUG. REMOVED ALL THE HOSES, IN WHICH CASE WAS A GOOD CALL BACAUSE ALL THE HOSES WERE HARD AND SOMEWHAT BRITTLE HENCE THE LEAKAGE.
TOOK A LITTLE TIME TO REPLACE THE HOSES BECAUSE I DID NOT WANT TO COMPLETELY REMOVE THE
... Read more FUEL TANK. IN ANY CASE GOT THE HOSE THREADED AND INSTALLED THE FUEL BULB... MACHINE STARTED RIGHT UP. WELL AFTER I ADDED FUEL THAT IS.
THANKS FOR THE PARTS AND THE SCEMATICS. i WOULD NOT HAVE BEEN ABLE TO DO THE REPAIR WITHOUT YOUR INFORMATION.
I HAVE USED THE SITE BEFORE LOOKIING FOR SCEMATICS AND ORDERING A FEW PARTS, OR IN SOME CASES WHEN THE PARTS ARE NO LONGER AVAILBLE,WHICH IS GFREAT TO KNOW. I CAN THEN CONCENTRATE ON PURCHASING A NEW MACHINE. It IS HELPFUL, IN THAT I CAN SHOW MY WIFE THAT THE PART IS NO LONGER AVAILABLE AND SHE IS MUCH MORE RESPONSIVE IN ALLOWING A BUDGET FOR A NEW MACHINE.
YOUR SITE SAVED MY MARRAIGE !!
NOT SURE IF YOU HAD HEARD THAT ONE YET..
MANY THANKS
JOE POTCH
Read less
Did you find this story helpful?
Thank you for voting!
The fuel bulb had broken open and was spilling gas.
Pull the cover, pushed the tab in and pushed the old bulb out. Detached the fuel lines. Pushed the new bulb in and attached fuel lines. Squeezed the bulb and couple of times and the weed whacker started right up.
Replace the whole start system and replace the whole carburator part\'s and for good measure I have replaced the reel and the job wet well and the trimmer is running like new condition.
Remove old upper shaft from housing - keep track of which screws go where
Insert new upper shaft
Align the screw holes properly and insert all screws.
Done.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9150685
Manufacturer Part Number: 791-610311B
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
