It is an authentic component which is supplied by the original equipment manufacturer. This electrode set is designed for use with Char-Broil grills. The electrode provides the spark that ignites the main burner. It is an identical replacement for a faulty or a missing item that was installed on a new unit. If the burner won't light, first clean the electrode and check that it's aligned. If the problem persists, replace the igniter electrode. Make sure to refer to the owners manual and the diagrams of your model for the correct installation of the new electrode set. You may need pliers to disconnect the old wires and connect the new component.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Easy
30 - 60 mins
(8 rated repairs)?
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
The burners and the crossover tubes on the grille were rusted through causing severe hot spots in some reason and overall undesired operation. I replaced the ignitor electrodes because they were inex
1. Shut off and disconnected the LP supply.
2.Removed the Grille grate and the 4 heat deflectors.
3. Removed retainer clips holding burners and cross over tubes.
4. Pulled burner tubes partially away from control valve and disconnected ignitor electrodes.
5. Removed all 4 burners tubes and 3 crossover tubes.
... Read more6. Unplugged the ignitor electrodes from the Spark module.
7. Took the opportunity to clean the inner fire box and inspect for any other signs of wear and tear.
8. Routed 4 ignitor electrodes through valve holes in firebox and plugged them on to the spark module
and snapped the other end of ignitor electrodes on to burner tubes.
9. Installed crossover tubes and clips onto burner tubes.
10. Reinstalled LP supply and checked operation.
11. Shut off grille and Reinstalled heat deflectors and grate.
Removed the grill grates and cleaned them
Removed the heat emitters and tossed them
Removed the flame tamers and cleaned them
Unplugged the burner electrodes and removed the rusted out burner tubes
Completely cleaned out the main box
Attached the new igniters to the new tubes and replaced the tubes
Ran
... Read morethe wires to the new ignition module and attached them
Attached the flame carryover tubes
Started the grill, testing each burner
Reset the flame tamers, heat emitters, and grill grates
This was a very simple repair.
Remove old rusted parts.
Minor clean up of the burner area.
Install replacement parts.
Everything fit in place correctly without modification.
Test for proper operation - good to go!
Steps to replace burners and carry-over tubes:
1) Take off grill grates
2) Remove cotter pins from burners
3) Pull burners and carry-over tubes out
4) Insert new burners
5) Insert new carry-over tubes
6) Insert new cotter pins
Ignition module required removing the gas pipe under the burner
... Read moreadjustment knobs with phillips screw gun...
Read less
Did you find this story helpful?
Thank you for voting!
Burner tubes, carryover tube, and started electrode all rusted and coming apart
Removed damaged parts
Went to eReplacementParts.com and ordered all needed parts by model. Parts arrived as promised and completed repairs with no tools needed within 15 minutes. Spent less than $50 and have a whole new grill.
Did you find this story helpful?
Thank you for voting!
Burners were rusted and igniters were not working.
Removed rusted parts and replaced them with new ones that were an exact match to the original parts. The only difficult part was threading the igniter wires thru to the push button starter.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10294604
Manufacturer Part Number: G350-0064-W1
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Grill","title":"Grill","url":"/parts/bbq/grill/"},{"position":2,"name":"Element or Burner","title":"Element or Burner","url":"/parts/bbq/grill/elements-and-burners/"},{"position":3,"name":"G350-0064-W1","title":"G350-0064-W1","url":""}]
