It is a genuine manufacturer approved replacement part designed for use with Homelite pressure washers. This gasket creates an air-tight seal for the carburetor. Over time it may shrink, deteriorate and crack eventually requiring replacement. It is a high quality composite material/rubber gasket that is sold individually.
1. Remove the engine from the frame.
2. Remove the carb heat shield.
3. Remove the pull rope assembly.
4. Replace the coil.
5. Replace the carb.
6. Reassemble.
1. Ordered parts that I thought might be required (received very quickly)
2. Put the entire Washer on a portable workbench
3. Removed wheels for easier access to mounting bolts and parts
4. unbolted motor mount for access to Nuts for housing cover for Air Breather and Carb
5. Replaced spark plug (adjusted Gap to sp
... Read moreecs)
6. Removed Air filter assembly for access to the carburetor - Disconnected and plugged fuel line
7. Disconnected throttle spring and bar
8. Removed old carb - slid off the two mounting bolts
9. replaced 1st gasket and slid on new Carb
10. reconnected, throttle spring, and bar replaced the front gasket
11. checked linkages
12. Reconnected fuel line and breather tube
12. Remounted Air Filter assembly replaced the two mounting Nuts
13. Reattached engine to the mounting bracket
14. Reattached Wheels
15. Tested and worked great
Note: it would not have been necessary to dismount the engine if there had been better clearance to the carburetor mounting nuts... Would have saved a lot of time.
1. Unbolted engine mount bolts
2. Unbolted 2 cap nuts on end of carb/air assembly/ w/choke on and gas in off position
3. Pulled off air cleaner assembly while carefully disconnecting air breather hose
4. Take off air cleaner gasket
5. Pulled gas hose off carb assembly after using pliers to slide spring clamp up 1 i
... Read morench from end(drain old gas into approved container)
6. 3 bolts hold gas tank, 2 under side of tank and 1 on other side going horizontally/ remove and slowly guide gas tank up and guide fuel line out as you remove tank/ remove spring clamp and replace hose/ if gas only trickled out of hose when draining also replace tank outlet which screws into tank/ inspect inside of tank for corrosion.
7. Pull off carb assembly - inspect gasket/ replace if needed(not usually needed to change) replace with new carb assembly.
8. Put tank back on while guiding fuel tube as was originally routed and connect to carb assembly and guide block/ use pliers and move clamp back to 1/2 inch from end of tube.
9. Put air assembly gasket back on- make sure that gasket is oriented correctly to air slot on carb assembly- place choke lever on carb so that it works on the butterfly valve on carb when moved
10. Place air assembly back on and connect air breather tube back on air breather/ put cap nuts back on and tighten firmly but not too tight.
11. Put engine back in place align bolts with nuts on top and tighten firmly.
Replaced the carburetor and gaskets. It started with one pull and washer ran great.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Pressure Washer","title":"Pressure Washer","url":"/parts/power-tool/pressure-washer/"},{"position":2,"name":"Seal or Gasket","title":"Seal or Gasket","url":"/parts/power-tool/pressure-washer/seals-and-gaskets/"},{"position":3,"name":"099980425068","title":"099980425068","url":""}]
