It is made of metal and is sold individually even though two may be needed during installation. The collector bearing fits next to the bearing bushing and the fan cover and helps to reduce friction. A screwdriver may be required when replacing the bearing. This is a Porter Cable replacement part directly sourced from the manufacturer for use in belt and disc sanders.
Troubleshooting
This part works with the following brands:
Porter Cable
This part works with the following products:
Sander Polisher
Part# 5140086-56 replaces these:
5140086-56,
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Great parts, great service as always.
I sanded some plastic which melted and a chunk hit the fan blade and broke it and some other parts. The fan bearings were also bad, so I got all the parts needed to fix my sander. GREAT!!! One issue was that the shaft was slightly too big in diameter for the bearings. A little light sanding and some lube and some careful force made it work. Sander works perfect now.
Woodrow - November 27, 2019
Verified Purchase
★★★★★
★★★★★
Belt/disc sander suction fan rebuild
Parts were ordered and shipped arriving in two to three days. Well packed and the correct parts.
EReplacement has my vote, thumbs up
Michel - December 30, 2020
Verified Purchase
★★★★★
★★★★★
Perfect.
Fit perfectly! Fast service. Porter Cable bench sander.
Guest - April 3, 2021
Verified Purchase
★★★★★
★★★★★
Good Seller Fast Delivery
Arrived quickly and got my bench top sander up and running again
Guest - September 22, 2021
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Remove all the guards (after unplugging the machine) and remove the screws holding the blower housing together and the unit with the pulley, bearings, shaft and fan will pull out. Remove the center screw in the fan, tap gently and the fan will come off. Remove the set screw on the pulley and remove the pulley, my set screw stripped and
... Read more I broke the pulley removing it. The replacement pulley did not come with a set screw, but the local hardware store had them. Remove the \"\"C\" clip and tap the shaft/bearing assembly out and then repeat holding the bearings in a vise and they will slide off easily too. As the directions say, reassembly is the reverse of assembly. I found that removing two small guards beside the belt made putting the belt back on easier. Just don\'t overtighten the screws into the plastic and it went back together very easily and now the unit runs like new for under $10.00 and a few minutes with a screwdriver. Thanks
Read less
Did you find this story helpful?
Thank you for voting!
Fan blade and fan cover broken while sanding plastic. A glob of plastic broke off and hit the fan.
Disassembled and found a bad bearing also. The bad bearing had also damaged the shaft.
Fan Housing not available - original cracked but usable. Used snap ring pliers to remove snap ring over bearings. Used 1/2\" drive socket that fit the bearings and used bench vice to press old bearings out. Note: Save the spacer between th
... Read moree bearings for reassembly. Had problem putting new shaft through new bearings. Sanded shaft lightly until fit was adequate and lubed the shaft and bearings to aid in the assembly process. Used socket and vice to press shaft through installed bearings. Used hammer and socket to gently center the bearings on the shaft and housing for best rotation. Easily done. The new fan blade fit to the new shaft was also a bit tight but with some careful and gently tapping it went on and the screw pulled it into place. Remainder of the assembly was straight forward.
Read less
Did you find this story helpful?
Thank you for voting!
Disc sander dust collection fan broke and fan bearings were tight
Removed dust collection housing assembly and disassembled. Removed damaged fan and bearings from damaged housing cover by pressing bearing and shaft assembly from housing cover. Pressed damaged bearings off bearing shaft and replaced with new bearings by pressing on to bearing shaft. Pressed bearings and shaft into new housing cover repl
... Read moreacing cir clip in housing cover. Replaced new fan to bearing shaft assembly and new cover. Reassembled dust collection housing by using existing housing and screws. Screwed new cover new bearings shaft and new fan to existing dust collection housing. Reassembled housing assembly to sander.
Removed covers and plastic shields
Removed hardware holding fan to main housing and removed fan
Reinstalled bearings in fan housing,
Reinstalled fan housing
Reinstalled all covers and shields
Ran to test
1 Disassembled unit found bad bearing and cracked cover
2 Ordered parts and they got here quickly
3 Reassembled bearing holder using a deep well socket and wooden mallet
4 Split ring pliers were a big help here
5 Put all parts back together after figuring out which roller to put the belt on first (top one lol)
... Read morer />
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP18982028
Manufacturer Part Number: 5140086-56
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
