This is a genuine Dewalt replacement part, it is sold individually.
Worn brushes frequently are the cause behind a motor running poorly.
• Replacing brushes can fix a motor that’s operating intermittently.
• New brushes can restore a motor’s electric braking.
Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Parts are just right.
Seller and parts was just what I was looking for.
Guest - May 10, 2019
Verified Purchase
★★★★★
★★★★★
DeWalt brushes
They fit and worked perfectly.
Joseph - June 20, 2019
Verified Purchase
★★★★★
★★★★★
Good parts
All the parts I purchased for my Dewalt grinder was good quality parts and its working perfectly.
Jonathan - April 25, 2020
Verified Purchase
★★★★★
★★★★★
Easy to order
The part that I order , was a Great fit
Thanks
Guest - February 4, 2021
Verified Purchase
★★★★★
★★★★★
Grinder Brushes
Had to replace the brushes in my grinder. Found the parts, ordered them, arrived in a few days, and then watched You Tube on how to replace them. Painless experience. Highly recommend ereplacementparts.com
Guest - January 21, 2023
Verified Purchase
★★★★★
★★★★★
Just like factory part
Showed up when promised and fit like original part.
Guest - May 19, 2021
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
Be the first to ask our experts a question about this part!
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
When the brushes failed, the arms that hold them against the armature were damaged. They were held in with #4 star drive screws (TINY!!) which I initially thought were Allen screws, they were that hard to see (and very difficult to approach, being tucked in behind the motor fan). I broke the arm mount in disassembly but with a certain am
... Read moreount of force and the replacement case, I\'m back in business. Should have removed the fan so I could see the mount screws with a magnifier (which is what I used) and would have saved the damaged mount/case and made a MUCH simpler repair.
1 Remove screws from brush covers
2 Using a curved pick gently pull red brush holders out to end of spring travel
3 Lift spring allowing brush holder to swing free.
4 Replace worn carbon brush.
5 Repeat steps in reverse order.
Did you find this story helpful?
Thank you for voting!
Existing brush door was missing, brush cable was broke.
removed old brush, inserted new brush. replaced missing cover door and screw.
DONE!
way cheaper than getting it repaired with a min 80 bucks to just look at it, shipping was fast and accurate. I use E Replacement parts often and would recommend them for any DIY person.
Removed the brush doors
Disconnected the brushes
Pull back the brush springs and rested them on the brush holder
Removed the old brushes and install the new ones
Replaced the brush springs
Installed the brush doors
I opened the bottom half of the grinder, (it is in a clam shell configuration). I then removed the arms and brushes using a allen wrench and small screw driver.Then put the new ones in place. Replaced the bottom half the grinder to its original form. And bam I am done easy as pie!
I took one brush doors off and saw that the brushes were burned out. Looked on line for replacement parts ,ordered them. When they arrived I removed the brush doors, then disconnected the old brushes, then connected the new brushes, then placed the brush doors back in place.
Grinder needed new brushes and the cord was damaged. Safety first, Put on eye protection. Cord was easily replaced by removing side cover and removing two screws holding cord wires to switch. Install cord protector on cord. Replace screws with new cord wires in place, reassemble cover. Brushes were also an easy remove and replace. Removed
... Read more brush covers by removing screw and opening cover. Pull back brush holder spring and lock on pin. Install new brushes by installing brush wire thru hole in brush holder and set brushes in holder and release brush holder spring from pin. Spring rest against brush holder, keeping tension between brushes and against armature. Plug brush wire into brush wire connector. Repeat for other side.Reinstall brush covers install screws to hold cover in place. Test Grinder for correct operation.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10183737
Manufacturer Part Number: 650918-01
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
