OEM Chicago Pneumatic Parts & Accessories

O-ring

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: A050268

This is an authentic replacement part that is supplied directly from original equipment manufacturer for use with Chicago Pneumatic nailers. It is one of the o-rings for the throttle valve. Over time seals and o-rings tend to wear out and deteriorate eventually requiring replacement. Please note this durable high quality rubber o-ring is sold individually.

Air Inlet Bushing

★★★★★

(1)

$9.13

Manufacturer Part Number:: CA147556

Piston

★★★★★

(1)

$76.95

Manufacturer Part Number:: P071926

The piston fits between the valve case and the cylinder. This is an OEM Chicago Pneumatic part directly sourced from the manufacturer for use in air hammers. This item is sold individually and is made out of metal. You may need a set of pliers when replacing this part. It will need to be replaced if it becomes broken.

O-ring

★★★★★

(5)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: A082777

This is a manufacturer sourced replacement part designed for use with Chicago Pneumatic ratchet/wrenchs. This o-ring provides an air-tight seal for the valve. Over time this o-ring will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of rubber and it is sold individually. Replacing this item you would need hex key/allen wrench and pliers...

Rotor Blade Set

★★★★★

(1)

$18.16

Manufacturer Part Number:: CA144889

This is a set authentic replacement rotor blades commonly used on Chicago Pneumatic power tools. Supplied from original equipment manufacturer. These blades are attached to the rotor and they will push the air inside the power tool. This set includes four (4) compound material blades per order. Replacing these blades is an easy job and will require a set of wrenches and pliers.

Valve Assembly

★★★★★

(2)

$20.55

Manufacturer Part Number:: 2050498953

This is a genuine manufacturer sourced replacement part designed for use with Chicago Pneumatic hammers. If your tool is leaking air or gets stuck, replacing firing valve assembly may resolve the issue. It is made out of black plastic and it is sold individually. To complete this repair you would need a screwdriver and pliers.

Gasket

★★★★★

(1)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: CA099895

Throttle Valve

★★★★★

(27)

$5.95

Manufacturer Part Number:: KF125190

Genuine Chicago Pneumatic replacement part, this item is sold individually. This part acts as as a seal so that air will not leak out of the throttle assembly on the tools shown below. Over time it will become brittle and crack. It is a good Idea to keep an extra one on hand.

Spring-throttle Valve

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: A117360

This item is sold individually and is made of metal. The throttle valve spring fits between the air inlet bushing and the o-ring. It may require a wrench during installation and will need to be replaced if it becomes bent or broken. This is an authentic part from Chicago Pneumatic for use in air hammers.

O-ring (-008)

★★★★★

(1)

$7.08

Minimum Quantity of 2 required

Manufacturer Part Number:: C079489

This o-ring is an authentic manufacturer sourced replacement part, it is not an aftermarket imitation. It is specially made for Chicago Pneumatic air hammers and sanders. It helps to provide an air tight seal between connected parts. Please make sure to check appropriate diagrams for correct location and use of this item. It is made from durable rubber and it is sold individually.

Spring-Throttle

★★★★★

(2)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: KF124390

This item is a genuine Chicago Pneumatic replacement part that has been sourced from the original manufacturer. The metal spring is used with pneumatic ratchets. This item is part of the throttle valve assembly and is used to provide compression for the valve when the throttle button is pressed. This item is available as an individual replacement part.

Retainer Buffer

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: 8940159856

This is an authentic OEM component from Chicago Pneumatic. The protective retainer buffer is made for use with the CP7120 (8941071200) Needle Scaler, and is fastened to the driver retainer on the barrel. The retainer buffer is sold individually. A flat head screwdriver and a pair of pliers may be necessary for the installation.

Chicago Pneumatic Parts

Popular Chicago Pneumatic Product Types

Popular Chicago Pneumatic Parts

Popular Chicago Pneumatic Models

All Chicago Pneumatic Product Types

Chicago Pneumatic Parts

Search By Model or Part Number

Popular Chicago Pneumatic Product Types

Popular Chicago Pneumatic Parts

Popular Chicago Pneumatic Models

All Chicago Pneumatic Product Types