Part Location Diagram of 753-06174 MTD Trimmer O-Ring
See part A-4 in the diagram
( Grid squares measure 1x1 inch )

Trimmer O-Ring 753-06174

Manufactured by:
MTD
ERP Number:
ERP9120828
Part Number:
753-06174
Original Equipment Manufacturer ?
  Works with your model  CS202!
In Stock
Delivers in 3-5 Business Days!
Minimum Quantity of 2 required

Easy 

15 - 30 mins 

(14 rated repairs) ?
  Works with your model   CS202!

Product Description

?

This authentic manufacturer-approved component which is specially designed for use with handheld lawn and garden equipment. The purpose of this o-ring is to provide an air-tight seal between connected parts, unfortunately, over time it may wear out and begin to crack eventually requiring a replacement. Please make sure to check appropriate diagrams of your model for the correct location and application of this o-ring. Keep in mind this high-quality item is made of durable rubber and is sold individually.

Frequently Purchased Together

?

Troubleshooting

This part works with the following brands:
  • MTD
  • Craftsman
  • Murray
  • Troy-Bilt
  • Bolens
  • Cub Cadet
  • Yard Machines
  • Yard Man
This part works with the following products:
  • Trimmer
  • Tiller
Part# 753-06174 replaces these:
753-06174, 753-06174-CM,

Customer Part Reviews

?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(1 Review)
Click to filter by ratings:
  • 5 stars
    1
  • 4 stars
    0
  • 3 stars
    0
  • 2 stars
    0
  • 1 star
    0
  • 1
Sort by:  
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

Easy 

15 - 30 mins 

(14 rated repairs) ?
  • 1
  • 2
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Trimmer O-ring leaking

Robert from lutz, Florida

5 of 5 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
753-06174
1. remove 3 screws
2. remove the cooler shield
3. remove old o-ring from crankcase cover
4. install new o-ring on crankcase cover
5. carefully align the rod and a cover, mount on the block
6. install cooler shield carefully align the 2 screws through the cover and a 3rd screw at top
Did you find this story helpful?
Thank you for voting!

Dog ear had snapped off, oring had failed.

John from Broken Arrow, Oklahoma

3 of 3 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
753-06173, 753-06174
Unscrewed the star drive screws holding the plastic housing and quick start, 3 were on the back and 1 was on the front. Quick start slides out easily, new one slides in with oring preinstalled. Screws go back in. This part came with a new oring already installed.
Did you find this story helpful?
Thank you for voting!

Changed out the short block. I broke a piston ring.

Randy from Kansas City , Missouri

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
Used a parts diagram for my trimmer and removed all the pieces then put them back with the diagram as a reference. Timed the coil with a business card.
Did you find this story helpful?
Thank you for voting!

Cover had hole in it o ring broken had no compression

Robert from Mishawaka, Indiana

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
753-06174
Removed 3 screws removed old cover installed new o ring on new cover installed cover with 3 screws.Weedwacker started right up.
Did you find this story helpful?
Thank you for voting!

trimmer stalled would not start

Michael from NORTHFIELD, Ohio

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Parts Used:
753-06174
Troy Bilt Trimmer
Remove rear plastic cover
remove metal crank case
remove old broken o ring
clean old oil and install new o ring
add blue locktite to bolts
reinstall plastic cover
Did you find this story helpful?
Thank you for voting!

Rear cover broke

Daphne from Lexington, Kentucky

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
753-06194, 753-06174
Remove the 3 screws install o-ring put cover on and put the screws back on and tighten them
Did you find this story helpful?
Thank you for voting!

Starter cover assembly broken

Charles from Frisco, Texas

1 person found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Replaced starter assembly and bad screw.
Adjusted carb and ran fine.
Did you find this story helpful?
Thank you for voting!

Bolt broken off and engine O ring blown

Steven from Tulsa, Oklahoma

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Parts Used:
753-06847, 753-06174
1. Removal of the back plastic motor housing with Torx driver.
2. Removal of motor housing.
3. Replace blown O ring with new and added a little oil on O ring.
4. Reinstalled parts and added new spark plug gapped at 0.025

Did you find this story helpful?
Thank you for voting!

Broken a ring and housing

james from Struthers, Ohio

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
753-06833, 753-06174
Removed old are seeing replaced new housing with new O-ring put it on unit fired right up
Did you find this story helpful?
Thank you for voting!

Blown o-ring seal; lost compression.

Scot from Lawrenceville, Georgia

0 of 1 people found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
753-06174
Replaced the old o-ring with the new. Seal fixed the problem.
Did you find this story helpful?
Thank you for voting!
  • 1
  • 2

Model Cross Reference

This part works with the following models:
ERP Number: ERP9120828
Manufacturer Part Number: 753-06174
Brand Model Number Description
Troy-Bilt 1154399 Trimmer - 1154399 - Trimmers
Troy-Bilt 1157403 Trimmer - 1157403 - Trimmers
MTD 21AK125G799 Tiller - MTD Tiller Model 21AK125G799 Parts
MTD 21AK125G800 Tiller - MTD Tiller Model 21AK125G800 Parts
MTD 21AK125G900 Tiller - MTD Tiller Model 21AK125G900 Parts
MTD 21AK125G965 Tiller - MTD Tiller Model 21AK125G965 Parts
MTD 21AK125G983 Tiller - MTD Tiller Model 21AK125G983 Parts
MTD 21AKC25C793 Cultivator - Farming
MTD 21BK125G983 Cultivator - Farming
Craftsman 316240320 Tiller - Tiller
Craftsman 316711020 Trimmer - Trimmer
Craftsman 316711021 Trimmer - Trimmer
Craftsman 316711022 Trimmer - Trimmer
Craftsman 316711023 Trimmer - Weedwacker Gas Trimmer
Craftsman 316711190 Trimmer - Trimmer
Craftsman 316711191 Trimmer - Trimmer
Craftsman 316711192 Trimmer - Trimmer
Craftsman 316711193 Trimmer - Line Trimmers/Weedwackers, Gas
Craftsman 316711370 Trimmer - Trimmer
Craftsman 316711390 Trimmer - Trimmer
Craftsman 316711470 Trimmer - Trimmer
Craftsman 316711471 Trimmer - Trimmer
Craftsman 316740820 Trimmer - Trimmer
Craftsman 316740890 Trimmer - Trimmer
Craftsman 31679102 Trimmer - Craftsman String Trimmer Model 316.79102 (31679102, 316 79102) Parts
Craftsman 316791020 Trimmer - Trimmer
Craftsman 316791160 Trimmer - Trimmer
Craftsman 316794370 Trimmer - Trimmer
Craftsman 316794371 Trimmer - Trimmer
Craftsman 316794450 Trimmer - Trimmer