This is a genuine OEM sourced replacement part used with Poulan hedge trimmers. A spark plug delivers electric current from an ignition system to an internal combustion engine. After time spark plugs will become dirty or fouled. It is a good idea to replace the spark plug once this happens. This item is sold individually. You should gap your spark plug according to the owners manual of the outdoor product you have. You would need a spark plug wrench or a socket wrench to install this component.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
perfect
the plug I needed
Guest - April 23, 2019
Verified Purchase
★★★★★
★★★★★
Outstanding In All Respects
Absolutely no complaints at all. I always go to eReplacementParts for my lawn equipment parts needs. They always provide the right part, in perfect condition, shipped quickly, and at a reasonable cost.
Guest - April 24, 2019
Verified Purchase
★★★★★
★★★★★
Great Company
I have ordered parts before and have found this company to be honest and very customer orientated. I will order again...thank you for being there...
JESS
Guest - May 17, 2019
Verified Purchase
★★★★★
★★★★★
Husqvarna Blower
Site made finding parts easy. Everything arrived quickly and in perfect condition.
Don - May 29, 2019
Verified Purchase
★★★★★
★★★★★
Fast delivery
Correct part fast delivery good EBayer
Guest - May 31, 2019
Verified Purchase
★★★★★
★★★★★
Worked as expected
You guys are AWESOME!! I've never had a problem with anybody from your staff. Your staff is very knowledgeable and pleasant to talk to. The order is always as ordered and arrives at the time it was supposed to. Just keep doing what you are doing and all will be well. Thank You
Guest - September 19, 2019
Verified Purchase
★★★★★
★★★★★
Arrived on time, works great
My leaf blower works great now.
Guest - November 18, 2019
Verified Purchase
★★★★★
★★★★★
Site easy to use and received it in a timely manner.
Part was received in excellent condition. Put it in my chainsaw as soon as I got it and started first pull!
Guest - April 30, 2020
Verified Purchase
★★★★★
★★★★★
Great Customer Service!
Excellent quality parts!
Guest - June 15, 2020
Verified Purchase
★★★★★
★★★★★
Easy
Great again
Guest - August 15, 2020
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
These are the steps i used... Remove fuel lines from carburetor note position of each. Open up cover of air box. Remove air filter. Remove two screws with Allen wrench. Remove air box. Slighty remove carburetor and unhook throttle cable linkage noting the way it hooks up. Remove carburetor. Make sure old gasket doesn\'t stick to carburet
... Read moreor adapter. Remove two screws and remove carburetor adapter. Take carburetor adapter, air box, and air box cover and clean with toothbrush and dishwash liquid. Dry thoroughly. Take a q-tip dip in cleaner and clean around cylinder where adapter fits. Push screws through carburetor adapter and put new gasket on screws pushing it on adapter so it lines up perfectly. Tighten adapter on cylinder. Push screws through air box, new carburetor, and place new gasket on screws against carburetor so gasket lines up perfectly. Install throttle linkage cable to carburetor. Tighten screws back down. Clean air filter, or replace then install air box cover. Hook fuel lines back up in proper position. Always, ALWAYS use non-ethanol gas in your weed eater with proper oil mixture. My Poulan weed eater is 13 years old and this is the first time I habe replaced anything on it.
Replaced fuel lines and other parts. Had to remove gas tank to get fuel lines through holes in top of tank. Tank comes off with rear housing of trimmer, 5 screws. Wait to cut fuel line to length until after tank is reattached.
1. Removed old fuel tank and spark plug.
2. Installed new tank with two original screws.
3. Attached new fuel lines to carburetor.
4. Installed new spark plug.
5. Put on new cutting line.
6. Good as new.
Removed fuel tank, attempted to push new fuel line into small holes, drilled holes slightly larger, run new fuel lines into the tank attached fuel filter, reattached tank, use RTV to plug slightly larger holes, the whole project took me 20 minutes.
Did you find this story helpful?
Thank you for voting!
Unit started extremely hard and would not run full-throttle.
Remove the carburetor and replaced all gaskets, fuel pump diaphragm and regulator diaphragm. Reseated bulb and replaced the gaskets which mate the carburetor to the engine\'s intake manifold. Once completed, I tightened all the bolts on the crankcase and engine head, replaced and gapped the spark plug. The unit started on the second
... Read more pull and is running great.
A quick note about the Walbro rebuild kit and the original parts in the carburetor. The fuel pump, for these carbs, in the original was a piece of blue plastic/mylar(?) that was solid. The replacement fuel pump looked like a mesh screen. That had me confused, for a bit. I did not realize that the replacement parts would look so different from the originals. That said, I should laugh at myself because this unit was made in 1996 and this is the first time it\'s been rebuilt. Things have changed, a bit, since them, obviously. LOL.
This was a quick, and easy job. If you can use a screwdriver you can do this work.
Remove the air filter assembly
Remove the fuel lines and throttle from the old carburetor
Remove the screws hold the carburetor on
Install the new carburetor and tighten the screws
Put the fuel lines and the throttle on the new carburetor
Replace the air filter assembly
Remove the old spark plug
... Read moreGapped the new one at 0.025
Disassembled complete blower. Removed cylinder, piston / ring assy from connecting rod, honed cylinder. Replaced piston, ring, and gaskets. Reassembled blower. Compression up to 140 psi. Started on second pull. This is a husqvarna 125b blower.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
3
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP17084452
Manufacturer Part Number: 530030179
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
