OEM Craftsman Circular Saw Parts & Accessories

BRUSH SET

$4.13

Manufacturer Part Number:: 1619X08020

Genuine manufacturer supplied replacement brush set designed for use with Craftsman worm drive saws. Due to constant contact with an armature brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. This assembly includes two (2) carbon brushes with lead wires and springs attached. Please note brush caps are sold separately. You would...

Power Cord

★★★★★

(18)

$31.81

Manufacturer Part Number:: 330079-98

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

Holder

★★★★★

(14)

$24.67

Manufacturer Part Number:: 147097-09

This brush and holder assembly is a genuine Dewalt replacement part, not aftermarket or generic. _b_This item is sold individually_/b_. As pictured, this item includes everything you need to replace a brush in your power tool. The brush, holder, terminals, and spring are included and ready for installation. If you only need the carbon brush and not this entire holder assembly, you can purchase ...

Switch Kit

★★★★★

(11)

$44.43

Manufacturer Part Number:: 429977-00

This Dewalt switch is a common replacement part and is compatible with the Dewalt tools listed below. This switch is a genuine Dewalt replacement part. It is a standard on/off switch and has four terminals. This switch has its four terminals located on the bottom, not the side, of the body but it is fully compatible with both configurations.

Retaining Ring

★★★★★

(4)

$5.37

Manufacturer Part Number:: 144803-00

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with circular saws and hammer drills. The special retaining ring is commonly used to secure the fan to the armature's shaft. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

Cord Protector

★★★★★

(12)

$6.43

Manufacturer Part Number:: 445338-00

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Outer Blade Clamp

★★★★★

(3)

$6.47

Manufacturer Part Number:: 145343-01

This is a genuine replacement outer blade clamp specially made for circular saws. This part helps to secure the blade to the unit. A wrench would be needed to remove the blade bolt when replacing this clamp. It is made out of metal and it is sold individually.

Assembly Brush

★★★★★

(4)

$6.15

Manufacturer Part Number:: 290075051

This brush assembly is an authentic Ryobi item, it is not an aftermarket imitation. It is sourced directly from original equipment manufacturer for use with circular saws and electric cultivator. This assembly includes (1) metal brush holder and (1) carbon brush with a lead wire and a spring attached. It is advised to replace both brushes at the same type. Please note, the hardware to secure this ...

Spring Washer

★★★★★

(7)

$2.99

Minimum Quantity of 2 required

Manufacturer Part Number:: 680776001

This is an authentic manufacturer-sourced part. It is specially designed for Ridgid and Ryobi circular saws. It helps to distribute the pressure evenly and provide a tight fit for the blade. If a spring washer on your equipment is damaged or is missing it will provide an identical replacement for the component that was included with a new unit. Keep in mind this high-quality hardware is made of du...

Bolt

★★★★★

(6)

$5.16

Minimum Quantity of 2 required

Manufacturer Part Number:: 145344-00

This is an OEM part sourced directly from the manufacturer. The screw is found in Craftsman circular saws. This is a metal part, used to hold other components to the spindle assembly. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

BLADE BOLT

$3.99

Minimum Quantity of 2 required

Manufacturer Part Number:: 2610000050

Brush and Spring

★★★★★

(45)

$10.27

Manufacturer Part Number:: 145323-06

This Genuine OEM carbon brush is an essential replacement part designed for use with a variety of DeWALT and Black & Decker saws. Sold individually, this high-quality component is made to conduct electrical current within the motor, enabling efficient power transfer and tool performance. Over time, carbon brushes naturally wear down due to friction and electrical contact, which can lead to intermi...

Craftsman Circular Saw Parts

Top Craftsman Circular Saw Models

Popular Craftsman Circular Saw Parts

Craftsman Circular Saw Models

Craftsman Circular Saw Parts

Search By Model or Part Number

Top Craftsman Circular Saw Models

Popular Craftsman Circular Saw Parts

Craftsman Circular Saw Models