This replacement part is supplied directly from the original equipment manufacturer. It is specially designed for Toro riding lawn mowers and garden tractors. The gear-pinion assembly is an important component which allows a user to steer the unit. It attaches to the steering shaft, and it interacts with gear-steering. This is an identical replacement for a damaged or a missing part that was installed on a new unit. Keep in mind this high-quality component is made of durable metal and is sold individually. Make sure to refer to the diagrams of your model for the correct installation of the new part. You will need a wrench set to perform this repair.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Good schematics
Ordering was simple based on schematics. Upon further diagnosis when parts arrived I ordered wrong parts. Return process, so far has been easy. Correct part arrived, fixed the problem.
Dan - May 24, 2019
Verified Purchase
★★★★★
★★★★★
Order Process
Ordering was simple for a non-computer gek. Parts I D was easy with the help of the chart boxes.
Guest - July 27, 2021
Verified Purchase
★★★★★
★★★★★
Have to replace every yr
Works great
Guest - November 18, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Remove nut and washer from steering shaft, pull shaft up 2 inches slide bearing out of hex hole, slide new bearing into hex hole drop shaft through bearing attach on washer reinstall nut and tighten. Use a small wire to pull and insert bearing
1. Removed the deck.
2. Pulled the bolt for the steering wheel.
3. Disconnected the brake and the gas pedal.
4. Pulled bolts for the plate.
5. Pulled bolts, replaced the steering gear.
6. Replaced the bearing flange.
7. Reinstalled the steering wheel shaft and the bolt.
8. Reinstalled the deck and
... Read more the cables.
Read less
Did you find this story helpful?
Thank you for voting!
Tractor would not steer...steering wheel spun in place
I removed the gas tank after draining it. I then removed the mower deck in order to access the steering gear more easily. I removed the old pinion gear and pulled the steering shaft out of the frame. The flange bearing was worn out so I had to drive it our from the bottom with a drift punch. I then set the new bearing in place, reinstal
... Read moreled the shaft, and installed the new pinion gear on the end of the shaft. I removed and sharpened blades while the deck was off, then put deck back on and reinstalled gas tank and attached fuel line. Mower steers and cuts great. This is the second time I have replaced that flange bearing...
Read less
Did you find this story helpful?
Thank you for voting!
Steering had locked up. Unable to steer the tractor.
1. Removed the deck.
2. Removed the pinion gear and the flange bearing.
3. Replaced gear and bearing and reassembled the steering unit.
4. Centered up the steering wheel and set the steering gear so it would have equal steering when turning the steering wheel from left to right.
Did you find this story helpful?
Thank you for voting!
Steering gear was partially stripped, bushings were worn, flange bushing was almost totally worn through, and drive belt was nearly broken.
Removed mower deck, jacked the mower up, removed steering pinion gear, removed electric clutch assembly, slid drive pully down crankshaft far enough to remove drive belt. Reverse procedure to reasemble. Slide steering shaft up and use punch to remove flange bearing, install new flange bearing, I was able slide it in place and get the stee
... Read morering shaft through it and position it and push it down with the shaft. Install new steering pinion gear. You must remove the battery and battery box to access belt pullies at transmission. Just watch what you are doing and don\'t get in a hurry.
Read less
Did you find this story helpful?
Thank you for voting!
Hex flange bearing failed stripping the steering pinion gear.
1.Remove the deck.
2.Remove the pinion gear.
3.Drop the plate above pinion gear to access hex bearing.
4.Install new hex bearing.
5.Reinstall plate.
6.Put the pinion gear on.
7.Reinstall the deck.
Did you find this story helpful?
Thank you for voting!
Steering was intermittent and one of the bearings had fallen out of one of the pulley assemblies.
1 - Removed the deck in order to better access the steering assembly and the pulley assembly.
2 - Replaced the gear-pinion on the steering assembly.
3 - Replaced the pulley assembly on the deck.
4 - Installed the deck and tested.
If you have access to a small battery operated impact driver it will make the job much
... Read more simpler.
Read less
Did you find this story helpful?
Thank you for voting!
Lawn mower started clicking while in drive then eventually would not go forward but reverse was fine. Gear on steering went also.
Removed wheels then took gear box off. Opened up, replaced gear drive with new unit add grease then re assembled. I then removed the steering wheel and removed the nut at the end of the steering shaft and replaced the gear on the shaft.
Lifted mower onto blocks
Removed gas tank for access to shaft
Removed 11/16\" nut from end of shaft
Remove old pinion gear and thrust washer
Lift steering shaft out of way and punch out worn bearing from below with screwdriver
Insert new hex flange bearing and shaft
Reinstall thrust washer and new g
... Read moreear
Reinstalled old 11/16\" shaft end nut as the one I received was an unusable shiny 10mm brass nut (probably the rack stancion nut) I thought I had ordered
Tightened shaft nut and reinstalled gas tank
Lowered mower and removed blocks then,
MOST IMPORTANTLY, checked and tightened steering wheel hub bolt as it had worked itself loose from all the wobbly action over time from the worn but now mostly new parts.
Works Great Now!
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_3.gif "Part Location Diagram of 112-0863 Toro Steering Pinion Gear")
_WW_3.gif "Part Location Diagram of 112-0863 Toro Steering Pinion Gear")
