This replacement spark plug is an authentic OEM sourced part, not an aftermarket imitation. It is specially designed for use on Toro lawn and garden equipment. A spark plug delivers electric current from an ignition system to an internal combustion engine. This item is sold individually. You will need a spark plug wrench or a socket wrench to replace the spark plug.
I to took a week for you folks to get my order to the USPS. When I called, a customer service lady stated that they had the order filled the next day after I placed it. She blamed the post office, that they were slow to update their information on line. I checked it out and it wasn't true.
MARK - July 25, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
The first step was to watch some of your excellent \"how to\" videos. I then took off the cowling to remove the Primer Button on the dash. Then removed the carburetor, disassembled it and sprayed it with carburetor cleaner and used the thin gauge wire to run through all the orifices, and re-sprayed it again. I had to review the videos
... Read more again because I forgot how to reassemble the needle valve into the float. Let me reiterate how excellent your videos are. I then trimmed the primer and gas line hose ends (they were cracked where the clamps are or in the pressed on areas). After reassembling the carburetor, linkage and hoses, and installing a new spark plug, I replaced the cowling, added the fuel mixture, primed once, full choked and cranked it. It started on the first pull. The blower is over 25 years old and works like new. Thanks for all the help I got from the videos and your quick response to the parts I ordered. Best regards, WES
Read less
Did you find this story helpful?
Thank you for voting!
27 year old snowblower that needed a new impeller. Like new again (almost...)
Pretty straight forward. Just took out the bolts and impeller, then put\'em back in. I did need a 3rd hand to get 2 of the bolts back in on the \'passenger side\'.
Did you find this story helpful?
Thank you for voting!
Needed primer bulb on my lawn boy mower and it was time
Removed three screws took off the shroud and carefully removed primer line popped out primer base then put in new base and primer bulb then replaced primer line put the shroud back on with the three screws. Then took a screwdriver and popped the clip off air cleaner cover and replaced air cleaner and cover. Removed spark plug wire rem
... Read moreoved plug and replaced with a new plug. Then replaced blade before attaching spark plug wire.
Changing rotor blade was difficult because of tight space to work in. Reassembling plastic covering and control panel was the most difficult. Had to loosen all bolts on front and rear covering to aline and reassemble. Drive belt, spark plug, gas lines and filter were the easiest. One bolt on drive belt side cover was worn down so much cou
... Read moreld not use wench, had to drill out and replace.
1. Removed old spark plug from mower.
2. Set new spark plug gap to .030 and installed it in mower.
3. Put 1 tablespoon of 30 weight motor oil onto new air filter.
4. Worked motor oil into filter by hand spreading it out evenly.
5. Blotted out excess motor oil from filter with a paper towel.
6. Cleaned mower a
... Read moreir filter housing of old oil and yard debris.
7. Installed new air filter.
8. Mower starts now with ease and runs great!
I had to remove part of the shroud covering the starter switch and dissemble the switch in order to install the switch boot. I also had to remove a side cover to gain access to the belt. Replacing the spark plug was a simple task whereas it was staring me in the face after removing part of the engine shroud. The parts I purchased were a p
... Read moreerfect fit. I will certainly order from eReplacements Parts again when needed.
Ken from Acushnet MA
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP8985099
Manufacturer Part Number: 50-1170
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
(1999)_WW_3.gif "Part Location Diagram of 50-1170 Toro Spark Plug")
(1999)_WW_3.gif "Part Location Diagram of 50-1170 Toro Spark Plug")
