This is an authentic OEM part for use with Husqvarna Lawn Mowers. The engine zone control cable stops the engine when you let go of the handle. The most common reason for replacing the cable is when the blades do not stop when the handlebar is released. This part is sold individually. The tool that you will need to replace the engine zone control cable is a socket wrench, screwdriver, scissors, snap ring and pliers.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Exact match!
The cable was a perfect match, only took about 5 minutes to change once the blade and dust guard were off. It wasn't my first purchase from eReplacement and it won't be my last ,my go to place for parts with great prices and near perfect parts.
Guest - July 1, 2019
Verified Purchase
★★★★★
★★★★★
cable blade
faster delivery and very helpful sales person
Richard - October 2, 2020
Verified Purchase
★★★★★
★★★★★
Perfect fit easy fix thx
Exact fit. Worked great back in Business!!!
Guest - December 10, 2022
Verified Purchase
★★★★★
★★★★★
Worked as expected.
Part is as expected. Price by the time it was delivered, $50.53, is stupid ridiculous! Next time I will shop for a used lawnmower, rather than pay such a "ripoff" price! One unhappy consumer!
Guest - May 9, 2023
Verified Purchase
★★★★★
★★★★★
Wrong part
The part arrived 8 days late. That was a problem since I paid for two day shipping, and the part was the wrong part, but that was my problem, I ordered the wrong part. I had to take my mower to a local repair shop.
Guest - May 23, 2020
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Removed blade, remove plastic cover by removing 1 screw underneath the mower and 2 small screws on top of the deck. Remove another plastic cowling under the deck by removing 4 small screws, 2 under the bagging chute cover and one on each side of the mower located between mower deck and rear wheels. Remove blade hub or blade holder, pull t
... Read morehe blade drive pulley (slid right off). Unscrewed the pulley on the transmission (that is mounted on the rear axle). This will give you slack in the drive belt and make it easier to pull the other half of the blade drive pulley, also I replaced this belt so it needed to come off anyway. Pulled the cable that engages the blade drive and installed the new one just like the old one comes off. Reinstall drive belt on pulley that is mounted to blade drive first and drive belt pulley on transmission second. Reinstall blade drive pulley, blade hub and blade. Replace covers and get after it.
Read less
Did you find this story helpful?
Thank you for voting!
Cable to engage the blade and the blade brake broke.
Gene from Sutter Creek, California
4 of 4 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
1. Removed the broken cable.
2. Removed the blade and the plastic shield around the belts.
3. Released the spring tension.
4. Ran the new cable.
5. Put it back together.
1. Removed the blade.
2. Removed screws and bolt holding plastic cover over blade.
3. Removed spring and retainer holding the cable under the mower.
4. Removed from handle bar the cable, pushed out.
5. Removed the Lever Assembly by squeezing together and re-installing new one.
6. Installed the cable reverse
... Read mored of how it was removed.
7. Started mower and tested blade action.
Read less
Did you find this story helpful?
Thank you for voting!
Broken blade actuator cable
Lawrence from CAMANO ISLAND, Washington
0 of 1 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Placed lawnmower on workbench on it\'s side to facilitate easier access to underside of mower deck. Removed blade and broken actuator cable. Installed new actuator cable and re-installed blade.
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9981965
Manufacturer Part Number: 579484202
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
