Part Location Diagram of V103000461 Echo Gasket-intake
See part I-11 in the diagram
( Grid squares measure 1x1 inch )

Gasket-intake V103000461

Manufactured by:
Echo
ERP Number:
ERP9234112
Part Number:
V103000461
Original Equipment Manufacturer ?
$7.57
In Stock
Delivers in 3-5 Business Days!
Minimum Quantity of 2 required

A Bit Difficult 

15 - 30 mins 

(3 rated repairs) ?

Does this part fit my model?

Need help finding your model number?

Product Description

?

This authentic item is supplied directly from the original equipment manufacturer for use with Echo gas powered backpack blowers. It helps to provide a tight seal for the intake manifold, over time it may wear out and begin to crack eventually requiring a replacement. Keep in mind this high-quality component is made of durable composite material and is sold individually. Make sure to check the appropriate diagrams of your model for the correct location and application of this hardware.

Troubleshooting

This part works with the following brands:
  • Echo
  • Shindaiwa
This part works with the following products:
  • Leaf Blower / Vacuum
Part# V103000461 replaces these:
V103000461,

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

Be the first to ask our experts a question about this part!

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

A Bit Difficult 

15 - 30 mins 

(3 rated repairs) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Only ran while modulating choke

Tom from Post Falls, Idaho

1 person found this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
I began by removing the plastic cage around the engine in the rear which is held in place by T-25 Torx screws and the air cleaner which is held in place by thumb screws. Once the cover is removed I removed the filter for inspection/replacement and behind it there are (2) phillips screws and (2) T-25 torx screws. I removed the (2) torx as these hold the back of the air box and carb. in place. The screws were around 3+\" in length and once removed with air box rear I was able to access the (2) fuel lines for disconnecting very easily. Mine were somewhat brittle and I cut about an 1/8th\" off in order to get back to more pliable line with easily enough left for reconnecting. The throttle cable was able to be disconnected with needle nose pliers from the carb. easily enough. I attempted to remove the reed valve behind this assembly however it was stuck in place pretty good and i did not want to break it just to replace a gasket which probably doesn\'t need replacing anyway so I skipped this. I installed the new carb. and all associated gaskets including rubber bushings and reassembled. I primed the carb. with the bulb a little more than usual until I felt fuel filling it up to ensure fuel had made it\'s way through the carb. set it to full choke full throttle and it started on the second pull! Runs like a champ again.

Thanks for being so reasonably priced!
Did you find this story helpful?
Thank you for voting!

carb was dirty bogging down on full speed

Richard from Fort Edward, New York

0 of 1 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set
changed air filter
changed fuel filter
changed spark plug
installed new carb

adjusted idle speed
adjusted hi and lo speed.
it now runs with no bogging down
Did you find this story helpful?
Thank you for voting!

Missing some parts carb gas lines gaskets and starter .

Harold from KENILWORTH, New Jersey

0 of 1 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
Replaced all of the parts that were missing .
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP9234112
Manufacturer Part Number: V103000461
Brand Model Number Description
Shindaiwa EB508RT Leaf Blower / Vacuum - Blowers Backpack
Echo PB-500 Leaf Blower / Vacuum - Blower
Echo PB-500H Leaf Blower / Vacuum - Backpack Blower
Echo PB-500T Leaf Blower / Vacuum - 50.8cc PBackpack ower Blower