This is an Genuine OEM replacement part used on Gas-Powered Handheld Trimmers. The purpose of this part is to mix air and gas before the fuel mix goes to the engine. If the engine won't start and the tank is full of fresh fuel, test the carburetor by removing the air filter and pouring about a teaspoon of fuel into the carburetor. Pull the starter rope. If the engine starts and then quickly dies, the carburetor is likely the problem. This Assembly includes a Metal Body Carburetor with Rubber Primer Bulb and Two (2) Rubber Fuel Lines. When replacing Carburetor it is advised that you also replace Carburetor Gaskets to ensure proper Air Tight Seal for optimum performance. You will need a Screwdriver to perform this repair.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Fixed the problem
Great part, easy to install (just 2 screws with a TroyBilt weed wacker.) The machined fired up after only 2 pulls and ran great! Carburetors are temper-mental devices and the small ones tend to fail after 4 or 5 years, even sooner if the lay-up maintenance for winter storage is not done. This one is an OEM replacement and I was really satisfied with it.
Guest - June 17, 2019
Verified Purchase
★★★★★
★★★★★
worked as it should
weed eater running great
Guest - June 22, 2019
Verified Purchase
★★★★★
★★★★★
Received part on time. Worked first time I primed the carb.
Worked first time I primed the carb. No adjustment needed for idle RPM.
Guest - July 8, 2019
Verified Purchase
★★★★★
★★★★★
New carb
Perfect fitment, came with exactly what I needed except a gasket (mine was still in great shape) runs perfectly.
Guest - April 25, 2020
Verified Purchase
★★★★★
★★★★★
Great and fast
Fast and easy received it in 3-4 days like they said I ft took 5 minutes to put it on works perfectly
Guest - April 30, 2020
Verified Purchase
★★★★★
★★★★★
Exactly what my weed whacker needed.
I've ordered several items from ereplacementparts and have been pleased every time. Thanks
Gordon - May 11, 2021
Verified Purchase
★★★★★
★★★★★
Exact fit
Quick response, correct part, packaged well and in excellent condition.
Guest - May 19, 2022
Verified Purchase
★★★★★
★★★★★
Toro weedeater
The carb. I received worked perfectly compared to the off brand I purchased previously that would not function properly.
Guest - June 3, 2022
Verified Purchase
★★★★★
★★★★★
Customer service is good. Everything went great. Thanks for your help. Have a good day.
Everything was good. Everything was great. I enjoyed dealing with you. Hope to deal with you again in the future.
Guest - March 16, 2024
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Checked spark. Good spark. Checked fuel flow into and out of carb. Good. Engine symptoms seemed to point to carb but could find no foreign debris in carb. No carb kit available so ordered new carb. New carb arrived very quickly even though I live on an island in PNW. Removed original carb. Found new carb throttle cable hole too sm
... Read moreall. Drilled out to fit with no problem. Mounted new carb with throttle cable attached with ease. Fuel lines required some sort of keeper whereas old carb was ridged to retain solid fit. Used stainless wire to compress fuel lines on carb pipes but will probably have to replace them in near future as wire cut into them. Engine started and continued to run but seemed to be a little lean with no choke. With about 1/3 choke it runs very well.I.. I\'ll leave the settings as they are for now. I am not a small engine mechanic. Repair was much better than just tossing what seemed to be basically a good engine. Very cost effective over the shop or a new power head. Very pleased.
Take off the filter cover and filter. Take off the gas lines and the throttle from the carburetor. Remove the two screws hold the carburetor. Take the old carburetor off and put the new one on, and screw in the screws. Put the gas lines and throttle on. Put the air filter and cover on.
Replaced carburetor by removing the air cleaner, then by removing the fuel lines and throttle. Then loosening two screws and removing the old carburetor. Then assembling in reverse order. Very simple.This was on a Ryobi trimmer.
Removed the air cleaner
Removed the gas lines and throttle from the old carburetor
Removed the screws holding the old carburetor on
Installed the gas lines and throttle to the new carburetor
Secured the new carburetor with the screws
Installed the air cleaner
Removed 4 screws on top of the carburetor, removed the old primer bulb and installed the new one. I did not need the new carburetor and did not use it. It is a shame you have to purchase the entire carburetor in order to get the primer bulb which probably costs no more than
$.50 to manufacture. I also replaced the air filter by
... Read moreopening the cover and taking out the old and in with the new one after applying a little motor oil to the new one to distribute the oil evenly throughout and removing excess oil by squeezing it in a paper towel.
I have not used the brushes yet. They are for a different tool which is somewhat more complicated, but not as urgent.
I was extremely pleased that I was able to get the parts that I needed and in a timely manner. Thank you for your prompt service. You might also like to know that I had ordered the brushes from Sears but they sent the wrong size twice and then I was unable to get them to reverse their charge to my account.
Removed \"C\" clip from old carburetor,
drilled correct sized hole for it on new carburetor
Place cable connector and C clip on new clip
Mounted new carburetor
Trimmer
- MTD String Trimmer Model 41AD26OG401 Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_2.gif "Part Location Diagram of 753-1225 MTD Carburetor with Primer")
_WW_2.gif "Part Location Diagram of 753-1225 MTD Carburetor with Primer")
