This is a genuine manufacturer-sourced part which is designed for use with Toro snowblowers. The clutch cable engages the deck. It is an identical replacement for a faulty or missing cable that was installed on a new unit. Check the appropriate diagrams for your model to ensure the correct repair procedure. Keep in mind this high-quality cable-clutch is sold as an individual item. You may need a screwdriver and pliers to perform this repair.
Troubleshooting
This part works with the following brands:
Toro
This part works with the following products:
Snow Blower
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
This was my daughter\'s snowblower so I wasn\'t familiar with it. Basically remove top cover and clutch side cover, cable is routed down through eye under crank shaft and then back up through eye on front side and connected to clutch lever. Opposite end of cable connects to link that is moved by handle. There was no routing shown on pa
... Read morerts drawing but a little common sense told me it had to go under shaft and back up to clutch activation lever, just had to locate the small eyes that cable is fed down through and back up to clutch activation lever
Read less
Did you find this story helpful?
Thank you for voting!
Snow paddle clutch cable broke ... the clutch cable guide became loose and broke. I believe the loose guide was the original source of the problem. I also replaced the belt
I found this fairly easy to accomplish ... It just takes a lot of words to describe the steps and pitfalls. Good luck.
Remove snow chute > 3 large screws
Finish by removing chute ring > 1 small screw
Remove 4 bolts that secure the red shroud
Remove gas cap
Remove shroud
Replace gas cap
Remove 2
... Read more screws and mounting clips holding bottom black shroud to blower handles
Remove 1 bolt > front lower right side of black shroud
Loosen shroud ... probably not necessary to remove it
Remove bolts securing belt, pulley cover
Remove cover ... lifting off tabs at bottom
TAKE A PICTURE SHOWING BELT ROUTING, PULLEYS, TENSIONING SPRING, BRACKETS ETC !!
Remove belt
>> unscrew and replaced broken clutch cable guide ... lubricate cable channel with silicon grease
>> feed replacement cable from lower back of blower into cavity ... up and around cable guide ... connect to clutch lever
>> route cable ABOVE blower handle ... connect upper end of cable to clutch handle actuator spring
>> REFER TO YOUR PICTURE
>> replace or install new belt
Replace pulley cover
Remount lower black shroud ... 2 clips & screws and 1 bolt
<><> feed the clutch cable THROUGH the left clip ... don\'t pinch it
<><> feed the 2 chute control cables through the right clip ... don\'t pinch them
Don\'t forget the bolt at the lower right front of the black shroud.
Reverse the rest of the steps!
Hope this helps =ƒÿÇ
Snow Blower
- Toro Snowblower Model 38751/SERIAL: 314000001-314999999 (38751/SERIAL:314000001314999999, 38751/SERIAL: 314000001 314999999) Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
(1999)_WW_5.gif "Part Location Diagram of 115-5682 Toro Cable-clutch")
(1999)_WW_5.gif "Part Location Diagram of 115-5682 Toro Cable-clutch")
