This is an authentic OEM sourced replacement momentary contact switch. It is specially designed for Homelite and Ryobi blowers and vacuums. It is the part of the tool handling on and off function of the tool. Please note, these mechanical switches have will over time wear out requiring replacement. This switch has a plastic body and it is sold individually. To replace this item no tools would be needed.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
It Works
The right part, easy to find, arrived quickly, works properly
Guest - May 25, 2019
Verified Purchase
★★★★★
★★★★★
Easy to install
I couldn't turn off the Ryobi leaf blower this year so I resorted to using choke and trigger to turn it off thinking that the whole blower had to be completely taken apart in order to fix the issue, and taking it apart might create other issues. However, I noticed some strange sounds coming from blower and it having difficulty going to full throttle. So, I researched online and was lucky to find this website having a part listing and took a chance on replacing this switch after reading reviews on this site of others fixing the issue by replacing the switch alone. Thankfully, it worked! For installation, I just took off the three screws in the handle to create a small gap on top of the handle and slid out the old one and inserted the new one into the same wires. The switch seems to be OEM and is more responsive than the old one. Thank you, eReplacementParts!
Guest - June 17, 2019
Verified Purchase
★★★★★
★★★★★
Easy Repair, Great Part, Works Great
The part was in very good condition when it arrived. I replaced the old switch with this one and the backpack blower now shuts off when I want it to!
Guest - July 29, 2019
Verified Purchase
★★★★★
★★★★★
Fast shipping
Guest - September 22, 2019
Verified Purchase
★★★★★
★★★★★
Part fit perfectly. The exploited views are great
Part fit perfectly. The exploited views are great.
Robert - October 24, 2019
Verified Purchase
★★★★★
★★★★★
KILL SWITCH REPLACEMENT
ARRIVED QUICKLY AND WORKED WELL. INSTALLATION WAS EASY
Guest - November 4, 2019
Verified Purchase
★★★★★
★★★★★
Got the part quickly!
My blower needed a switch, came quickly, was the correct one! What more could I ask for.
Guest - June 30, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Take your time in removing each of the screws holding the housing pieces to the motor. Each set of screwn needs to be kept together and marked so they go back to the same places. I just kept taking off piece after piece until I got to the parts needing replaced. Take it off and put on the new one then reverse the process until it is al
... Read morel back together.
Took off 7 screws around the housing, disconnected the old switch, slid out old switch, connected the new switch, slid in new one, and put screws back.
1. Remove handle screws.
2. Unhook wires from switch and install new switch.
3. Replace handle as not to pinch wires, install screws and tighten.
4. Loosen clamp screw, remove bellows.
5. Remove old clamp, install new clamp, install bellows, tighten.
1. Remove the screws from the little cover
2. Remove the screws from the big cover
3.un hook the two wires
4. Plug the wires back in to the new switch
5. Put the covers back on
1. Removed the engine cover. (4 screws - T20 Torx bit)
2. Split the throttle trigger handle. (3 screws - T25 Torx bit)
3. Removed the bad switch (unplugged two wires).
4. Installed the new switch (plugged in two wires).
5. Replaced the throttle trigger handle cover and the engine cover.
Did you find this story helpful?
Thank you for voting!
Blower kill switch got tired after 12 years of use!
1. Disassembled the handle with star bits
2. Disconnected 2 wires
3. Removed switch
4. Installed new switch
5. connected wires
6. Reassembled handle
7. Tested unit by starting and shutting down
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP18789306
Manufacturer Part Number: 760338004
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
