This idler gear is supplied directly from the original equipment manufacturer. The poly plastic gear is made for use with the Penn 9M Special Purpose Levelwind Reel. This gear is fitted into the left side plate assembly, balancing the speed with the worm gear. A screwdriver is required for the repair. The idler gear is sold individually. However, it is also included with the left side plate assembly (1182148).
Troubleshooting
This part works with the following brands:
Penn
This part works with the following products:
Conventional Reels
★
Customer Part Reviews
?
5.0
Average Rating (out of 5):
★★★★★
★★★★★
(2 Reviews)
Click to filter by ratings:
5 stars
2
4 stars
0
3 stars
0
2 stars
0
1 star
0
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Penn reel Parts - Best source
Received the replacement gear. Arrived quickly. Good packaging.
Guest - July 24, 2020
Verified Purchase
★★★★★
★★★★★
Great customer service.
Part arrived quickly and order was correct.
Guest - July 23, 2021
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1.Remove screws on clicker side cover
2.Remove worm shaft
3.Remove worm shaft cover just to get out of way
4.Remove idler gear screw
5.Remove idler gear replace with new
6.Reinstall idler gear screw
7.Reinstall worm shaft cover and worm shaft
8.Reinstall cover and reinstall screws
Did you find this story helpful?
Thank you for voting!
Penn #9m conventional reel - the nylon idler gear was broken
1 - Remove the left side of the reel (plate opposite the handle)
2 - Remove the screw holding the clip for the clicker
3 - Remove the clip
4 - Remove the gear (nylon idler gear)1184060), replace it with new gear
5 - Clean off the internal parts, reapply Penn reel grease
6 - Continue to assemble the reel
Did you find this story helpful?
Thank you for voting!
Idler gear was stripped so level wind would not work
1. Remove handle
2. Remove faceplate screws
3. Pull off faceplate and spool
4. Remove clicker vise screw and clicker vise
5. Remove idler gear screw and old idler gear
6. Install new idler gear
7. Follow steps in reverse to put reel back together
Unscrewed one side.
Replaced plastic gear.
The Pawl cover was a little tricky putting it back on.
Its basically common sense.
Now the reel level wind works fantastic.
Would have done it 20 years ago if I knew it was that easy.
That\'s how old my reel is.
Did you find this story helpful?
Thank you for voting!
Idler gear stripped teeth due to worm gear and paw worn out and locked!
I totally took reel apart oiled and greased everything needed put back together and done, thanks until next time!
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
