This is an OEM part sourced directly from the manufacturer. The plain washer is commonly found in power tools from Black & Decker, such as drills, hedge trimmers, and blower vacs. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different washers used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You may require a screwdriver, wrench, or pliers when replacing this item. The plain washer is available as an individual replacement part.
Troubleshooting
This part works with the following brands:
Black and Decker
Craftsman
Stanley
DeVilbiss
DeWALT
This part works with the following products:
Hedge Trimmer
Electric Drill
Leaf Blower / Vacuum
Boring Machine
Hammer Drill
Sander Polisher
Part# 148902-00 replaces these:
148902-00, P148902-00,
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
1. Removed the shroud.
2. Removed the nut - THIS IS A REVERSE THREAD NUT!
3. Removed the fan.
4. Replaced the fan.
5. Replaced the nut - I STRIPPED THREAD ON OLD NUT BY TRYING TO TURN COUNTER CLOCKWISE ON REMOVAL
6. Replaced the shroud.
1. Disassembled the blower/vac clamshell housing by unscrewing the six Torx T15-head screws. Two of the screws are sunk deep below the housing surface, so I could not use the T15 head that I already owned as part of my ratchet set. Went to hardware store to buy a Torx T15 screwdriver with a shaft long enough to reach the screw heads from
... Read moreoutside the shell.
2. Removed the hard plastic \"fan\" that shreds the leaves, etc. This required removing the plastic nut that holds it on, which I did using my socket set.
3. Put the new fan on after recycling the old one, screwing on a new plastic nut with my socket wrench.
4. Fit the old vacuum tube, which was not damaged, into the new clamshell housing and reassembled the clamshell using the original screws, which were all in excellent condition.
5. Cleaned off the old clamshell housing and put it into the recycling bin.
6. All done, literally as good as new, in about 20 minutes.
1. Remove handle and blade guard.
2. Remove all screws. Screw has star and blade slot.
3. Separate two halves.
4. Use latex gloves.
5. Remove all parts from the motor to the blade gear.
6. Remove the grease that is contaminated with iron fillings from the stripped gear.
7. Add half the tube of new grea
... Read morese.
8. Starting at motor, assemble the new parts, slide them into place.
9. Add the remaining grease.
10. At this point, I replaced the switch lock.
11. Assemble the halves and replaces the screws.
The screws are self threading. Turn the screw to the left to feel a little click. Tighten screw.
12. Replace the blade guard and handle.
13. Clean the blade and lubricate it.
14. Test to verify the Hedge Trimmer is running properly.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10166293
Manufacturer Part Number: 148902-00
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
