Close
Phone 1-855-343-0069
Cart
Official OEM Guarantee
Fast shipping from USA
365 Day Returns
Preferred Brand Partners
10126340-1-M-Milwaukee-32-10-0132-Gear Assembly
Part Location Diagram of 32-10-0132 Milwaukee Gear Assembly
See part 16 in the diagram
( Grid squares measure 1x1 inch )
10126340-1-S-Milwaukee-32-10-0132-Gear Assembly Part Location Diagram of 32-10-0132 Milwaukee Gear Assembly

Gear Assembly 32-10-0132

Manufactured by:
Milwaukee
ERP Number:
ERP10126340
Part Number:
32-10-0132
Original Equipment Manufacturer ?
$65.50
Special Order

A Bit Difficult 

More than 2 hours 

(1 rated repair) ?

Does this part fit my model?

Need help finding your model number?

Jump to:

Description Troubleshooting Questions & Answers Repair Instructions Model Cross Reference

Product Description

?

This is an original part from Milwaukee. The gear assembly is made for use with the Two Speed Hole Hawg Drill. This metal and plastic component is fitted between thrust washers, driving the shaft. The gear assembly is sold individually. A screwdriver and socket set are needed for the removal and replacement.

Troubleshooting

This part works with the following brands:
  • Milwaukee
This part works with the following products:
  • Electric Drill

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

A Bit Difficult 

More than 2 hours 

(1 rated repair) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Both, clutches were worn out along with the chuck.

Todd from Concord, California

3 of 3 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers, Socket set
Parts Used:
48-66-1381, 45-88-7100, 44-70-0160, 40-50-7670, 36-66-1675, 32-10-0132, 32-10-0122, 22-18-0670
Milwaukee Hole Hawg, 413B. Removed the chuck along with the screw in the center. It\'s reversed threads, tightened up a 3/8 allen wrench in the chuck & hit it with my dead blow hammer. Carefully remove the rear cover, be careful because you need to lift it off and wiggle it evenly straight up. If one of the gears doesn\'t let loose fr om the cover just stick your finger in & push down on the gear and pull straight up on the cover until it breaks loose. There\'s a certain order that everything comes out. Print out the parts sheet so you know what to expect and lay everything out. I carefully cleaned up the parts, removed old grease inside & clean out with solvent.
Read less
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP10126340
Manufacturer Part Number: 32-10-0132
Brand Model Number Description
Milwaukee 1675-1 Electric Drill - Two Speed Hole Hawg Drill
Milwaukee 1675-6 Electric Drill - Milwaukee 1675-6 Parts
Milwaukee 1678-20 Electric Drill - Electric Drill / Driver
Milwaukee 1679-01 Electric Drill - Electric Drill / Driver
Milwaukee 1679-1 Electric Drill - Milwaukee 1679-1-(915a) Parts
Gear Assembly
$ 65.50
Special Order
✖
Stock Status
✖
Mail-In Recycling Rebate

Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.

✖