Part Location Diagram of 06-82-5363 Milwaukee 8-32 X 1 Wshr Hd Tt T20 Sc
See part 7 in the diagram
( Grid squares measure 1x1 inch )

8-32 X 1 Wshr Hd Tt T20 Sc 06-82-5363

Manufactured by:
Milwaukee
ERP Number:
ERP10118965
Part Number:
06-82-5363
Original Equipment Manufacturer ?
$6.16
Special Order

A Bit Difficult 

More than 2 hours 

(1 rated repair) ?

Does this part fit my model?

Need help finding your model number?

Product Description

?

This is a genuine replacement part sourced directly from the manufacturer. The screw is commonly found in Milwaukee Sawzalls. This part is made of metal, and is generally used to secure the gear case. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You may require a torx screwdriver or Allen wrench when replacing this item. The screw is sold as an individual replacement part.

Troubleshooting

This part works with the following brands:
  • Milwaukee
This part works with the following products:
  • Reciprocating Saw
  • Saw

Questions & Answers

?

Our customer Service team is at the ready daily to answer your part and product questions.

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Ask our Team

We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

Does this fit my product?

Customer Repair Instructions

All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

A Bit Difficult 

More than 2 hours 

(1 rated repair) ?
  • 1
Sort by:  
Sorry, we couldn't find any existing installation instruction that matched.

Sawzall blade didn\'t move, motor was fine.

Paul from Northboro, Massachusetts

2 of 2 people found this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Socket set
Remove rubber overmold
Remove gearbox
Remove drive shaft and wobbler arm
Remove retaining rings on wobbler arm and drive shaft
Use a hammer head to bang out the outer bearing race from the wobbler arm
Use a bearing splitter to remove the inner bearing race from the drive shaft. Could not remove them without a splitter.
Clean the surfaces before installing the new bearings
Slide the wobbler retaining ring on the drive shaft before installing the bearings
Install the new bearings on the drive shaft. Use a socket to hammer them on. Can freeze the shaft for a day to shrink it a bit.
Install the wobbler arm over the bearings. Slight pressure with a vise helps to slide the bearings into the wobbler arm.
Install the retaining rings.
Clean old grease from the gearbox.
Apply new grease to the gearbox, bearings, blade arm.
Reassemble gearbox to drive motor.
Reinstall rubber overmold.
Reinstall blade shoe.
Did you find this story helpful?
Thank you for voting!
  • 1

Model Cross Reference

This part works with the following models:
ERP Number: ERP10118965
Manufacturer Part Number: 06-82-5363
Brand Model Number Description
Milwaukee 0719-20 Reciprocating Saw - V28 Sawzall Reciprocating Saw
Milwaukee 0719-22 Reciprocating Saw - Cordless Sawzall
Milwaukee 0719-50 Saw - Milwaukee 0719-50-(A56a) Parts
Milwaukee 0819-50 Reciprocating Saw - Cordless Sawzall
Milwaukee 6509-20 Reciprocating Saw - Sawzall
Milwaukee 6509-22 Reciprocating Saw - Sawzall
Milwaukee 6509-68 Saw - Milwaukee 6509-68-(00010705) Parts
Milwaukee 6515-20 Reciprocating Saw - 18 Volt Sawzall Recip Saw
Milwaukee 6515-50 Reciprocating Saw - Cordless Sawzall
Milwaukee 6519-22 Reciprocating Saw - Sawzall
Milwaukee 6521-21 Reciprocating Saw - Sawzall
Milwaukee 6521-51 Saw - Milwaukee 6521-51(981d) Parts
Milwaukee 6521-55 Saw - Milwaukee 6521-55-(A30a) Parts