This is an OEM replacement part, sold individually. This Grommet is an elbow for the crankcase breather tube. These rubber elbows were just a convenient way to make a 90 degree bend back when they used metal tubing. Compatible with the equipment shown below.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Prompt shipment, perfect fit. I will use this supplier again.
As noted
Donald - August 2, 2019
Verified Purchase
★★★★★
★★★★★
Factory part for an old machine
Purchased an older aerator with a Briggs engine on it - The engine needed a tune up along with this vacum grommet.
E-replacement parts is my go-to source for my machines. Convenient ordering, competitive pricing and they even have tutorials and suggestions for your household appliance needs.
Scott - October 4, 2019
Verified Purchase
★★★★★
★★★★★
carburetor rebuild
Had a very good experience with purchasing my part. I spoke with Mary on the initial call but realized I needed further assistance and parts to be ordered. I do not remember the names of the other two who helped me with my order but considering the order took many weeks to arrive it was one of the best experiences I’ve have ordering something. My order was placed in the early days of the pandemic so it was understandable when stocking and shipping were disrupted. The experience was made by the staff working the phones while placing the order. The ladies I spoke with were proficient, professional and personable. Thank you.
Guest - June 5, 2020
Verified Purchase
★★★★★
★★★★★
It's the little parts
Needed the parts to make it correct, perfect fit, arrived quick, made the job professional.
William - June 15, 2020
Verified Purchase
★★★★★
★★★★★
Easy repair
Great part arrived sooner than I expected!! Works great =ƒæì
Guest - July 13, 2020
Verified Purchase
★★★★★
★★★★★
Great Parts
Thank you for fast shipment parts fit great.
Karl - July 11, 2020
Verified Purchase
★★★★★
★★★★★
Perfect fit
It’s as good as the factory part
Guest - July 17, 2020
Verified Purchase
★★★★★
★★★★★
Parts I needed + more
Ordered with carb rebuild kit. All parts I needed to rebuild carb plus many extra parts to fit variations of that model carb. Repaired carb and motor runs better than new.
Guest - February 3, 2021
Verified Purchase
★★★★★
★★★★★
Exactly the right part.
The part was a perfect fit.
Guest - July 13, 2021
Verified Purchase
★★★★★
★★★★★
Part was just what I needed
Fast service, fast shipping, thanks.
Guest - August 9, 2021
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Grommet was missing. Ordered new grommet and spark plug Removed the old spark plug and gapped the new one at 0.030. After replacing these parts and adding gas, mower cranked after numerous pulls. After cutting the grass the mower now cranks on first pull. This mower had not been cranked in over a year. I also mixed \"Mechanic in a Bottle
... Read more\" with the gas.
Read less
Did you find this story helpful?
Thank you for voting!
Engine wouldn\'t start because the rubber connectors were cracked
Remove the breather tube, and both grommets from the breather assembly. Remove the old grommets and installed the new grommets. Remove the air cleaner cover and remove the old pre filter and install the new on, then place the cover back on.
Did you find this story helpful?
Thank you for voting!
Very bad engine misfire, could not be corrected with needle valve adjustment or carb cleaning
1. Removed carburetor and separated top from bottom
2. Saw very slight wrinkle close to spring on fuel pump
3. Replaced membrane, pump spring and breather grommet. Likely only the membrane was worn.
4. Reinstalled carburetor and engine started right up and ran like new!
Did you find this story helpful?
Thank you for voting!
The engine wouldn\'t turn over and water damage was evident.
Garren from Lewisville , Texas
4 of 4 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
I removed the lever panel, gas tank, and carborater in that order. I cut a new gasket for the carb to rest on, flushed the carb with cleaner, flushed the gas tank with fresh gas, replaced the diaphram, and reassembled. Finally adding the air filter and replacing the cap. She cranked up after ten pulls. The grommets had weathered and neede
... Read mored replacing. Other than that, it was pretty straight forward.
Read less
Did you find this story helpful?
Thank you for voting!
Motor had set up for several years. Gaskets and grommets were bad.
Ordered carburetor for a 25 yo Pollen Garden teller w/Brigs 5 hp engine. Two screw holes had to be opened up with tap. Ordered later two grommets that were needed to replace the old parts. Most difficult to replace this carb. on this engine. When done Just two pulls and purring like a kitten. Good carb.
Did you find this story helpful?
Thank you for voting!
The carburetor diaphragm was old and no longer worked.
Remove the four screws that hold the diaphragm cover plate to the carburetor.
Remove the cover plate. Notice the orientation of the diaphragm and remove it. At this point spray some carb cleaner through the orifices to remove any debris.
Place the new diaphragm on the carburetor (there is only one way the diaphragm will fit)
... Read moreand attach the cover plate to the carburetor with the four screws.
Too off air breather to get to carb. Unbolted gas tank and carb. Used tools to take apart carb. Scraped old gaskets off carb. Used carb cleaner spray and compressed air to spray our all holes and cleaned carb. Put new gaskets on then fired right up. Will deff use in the future for parts etc.
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
(1979)_WW_4.gif "Part Location Diagram of 692189 Briggs and Stratton Grommet")
(1979)_WW_4.gif "Part Location Diagram of 692189 Briggs and Stratton Grommet")
