OEM Makita Hammer Drill Parts & Accessories

$14.06

Manufacturer Part Number:: CB351

This is a Genuine Manufacturer Sourced replacement part used on Makita Rotary Hammers. Includes Two (2) Carbon Brushes with Lead Wires attached. Please note Brush Holders and Springs are Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they ...

Power Cord

★★★★★

(29)

$33.86

Manufacturer Part Number:: 664064-4

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sol...

Compression Spring 3

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: 231403-9

This is an authentic OEM part. The Makita compression spring 3 is constructed of metal, and is compatible with the HK1810 Scraper. This part is secured between the steel ball and tool holder, helping the device to hold specific scraping tools. This part is sold individually. A wrench is helpful in the removal and replacement.

Carbon Brush Set

★★★★★

(2)

$16.00

Manufacturer Part Number:: CB175

Genuine Manufacturer Sourced replacement part. This item is made out of Carbon with a Lead Wire attached. This item includes Two (2) Carbon Brushes per order. Please note Brush Holder and Spring are Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear...

Carbon Brush Set

★★★★★

(10)

$18.43

Manufacturer Part Number:: CB407

This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New b...

O Ring 28

★★★★★

(1)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: 213415-4

This is a genuine replacement part designed for use with Makita power tools. This o-ring provides an air-tight seal for the connected parts. Please make sure to check appropriate diagrams for location and use of this item. Over time o-rings will shrink, become brittle and crack allowing for air leaks. At that time they should be replaced. It is made out of rubber and it is sold individually.

Brush Holder Unit

$18.72

Manufacturer Part Number:: 632D00-2

This replacement brush holder unit is a high quality item that is supplied by original equipment manufacturer for use with Makita demolition hammers. Its purpose is to secure carbon brushes around the armature to maintain stable contact. This item is a complete assembly which includes the plastic ring, two metal brush holder with attached lead wires, please note the carbon brushes themselves are s...

Ball Bearing

★★★★★

(2)

$25.16

Manufacturer Part Number:: 211031-6

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. This reduces wear on the tool, allowing it ...

Cord Guard

★★★★★

(5)

$5.95

Manufacturer Part Number:: 682502-4

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually require replacement. Keeping a strong cord guard on your tool ...

Ball Bearing 6000ddw

$15.15

Manufacturer Part Number:: 210059-1

This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.

Carbon Brush Set

★★★★★

(20)

$10.90

Manufacturer Part Number:: CB325

Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through...

O-ring

★★★★★

(2)

$7.60

Minimum Quantity of 2 required

Manufacturer Part Number:: 213962-5

This replacement o-ring is specially designed for use with Makita rotary hammers. It is an authentic manufacturer sourced item that is used to provide a seal for the striker and the piston. For correct location please make sure to check appropriate diagrams of your unit. Over time seals and o-rings tend to shrink, become brittle and crack eventually requiring replacement. Please note one durable r...

Makita Hammer Drill Parts

Top Makita Hammer Drill Models

Popular Makita Hammer Drill Parts

Makita Hammer Drill Models

Shop by Popular Makita Hammer Drill Part Types

Makita Hammer Drill Parts

Search By Model or Part Number

Top Makita Hammer Drill Models

Popular Makita Hammer Drill Parts

Makita Hammer Drill Models

Shop by Popular Makita Hammer Drill Part Types