
We Sell Only Genuine Makita® Parts.
Makita Plate Joiner Parts & Models
Popular Makita Plate Joiner Parts

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible.
Power Cord Specifications:

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually require replacement. Keeping a strong cord guard on your tool will help will cord life.
This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

Set of 2 Carbon Brushes with wire leads and brush springs attached.
The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box.
This brush set will fit the Makita tools listed at the bottom of the page.
• Worn brushes are frequently the cause of a poorly running motor.
• Replacing brushes can fix an intermittently operating motor.
• New brushes can restore a motor’s electric braking.
Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

This is a genuine Makita replacement part, it is sold individually.
It is part of the bit holder. Without this Ball the bit would not stay in the holder. It is used in a number of different tools for different reasons. But it is most popular in Cordless Impact Drivers and Corded Screw Drivers.
Compatible with the tools listed below.
The diameter is 3.5mm.

This #191938-1 (CB-408) Makita carbon brush set contains two individual carbon brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box.
This brush set will fit the Makita tools listed at the bottom of the page.
• Worn brushes are often the cause of a poorly running motor
• Replacing brushes can fix an intermittent motor
• New brushes can restore a motor’s electric braking
Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sold separately.
Replacing this power supply cord you will need a screwdriver.
• Remove the housing screws
• Remove the the housing
• Disconnect the old cord wires
• Remove the old power cord
• Secure the new cord in place
• Connect the wires
• Reassemble and test the new cord

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Over time, power tool cords will wear out or become frayed. We recommend replacing a cord as soon as signs of wear are visible.
Power Cord Specifications:

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually require replacement. Keeping a strong cord guard on your tool will help will cord life.
This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

Set of 2 Carbon Brushes with wire leads and brush springs attached.
The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box.
This brush set will fit the Makita tools listed at the bottom of the page.
• Worn brushes are frequently the cause of a poorly running motor.
• Replacing brushes can fix an intermittently operating motor.
• New brushes can restore a motor’s electric braking.
Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

This is a genuine Makita replacement part, it is sold individually.
It is part of the bit holder. Without this Ball the bit would not stay in the holder. It is used in a number of different tools for different reasons. But it is most popular in Cordless Impact Drivers and Corded Screw Drivers.
Compatible with the tools listed below.
The diameter is 3.5mm.

This #191938-1 (CB-408) Makita carbon brush set contains two individual carbon brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box.
This brush set will fit the Makita tools listed at the bottom of the page.
• Worn brushes are often the cause of a poorly running motor
• Replacing brushes can fix an intermittent motor
• New brushes can restore a motor’s electric braking
Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sold separately.
Replacing this power supply cord you will need a screwdriver.
• Remove the housing screws
• Remove the the housing
• Disconnect the old cord wires
• Remove the old power cord
• Secure the new cord in place
• Connect the wires
• Reassemble and test the new cord