It is an authentic item that is designed for use with Husqvarna, Poulan and Weed Eater riding lawn mowers and garden tractors. This is the left-hand draglink that connects to the spindle and the gear-selector plate allowing the user to steer the mower. If the part is damaged or is missing, this authentic item will provide an identical replacement. Refer to the diagrams of your model for the exact location and the correct installation of the new part. To perform this repair you will need a set of wrenches. Keep in mind, the hardware to secure it and the left-hand draglink is sold separately.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Drag link
Fit great
Guest - September 17, 2019
Verified Purchase
★★★★★
★★★★★
Worked great
Replaced new part with ease. Old part was now easy to remove but new part went on without any problem.
Guest - October 15, 2019
Verified Purchase
★★★★★
★★★★★
Great part!
Arrived quickly, was in great condition
Guest - November 25, 2019
Verified Purchase
★★★★★
★★★★★
Easy Fix
Part worked great easy install
Guest - June 24, 2020
Verified Purchase
★★★★★
★★★★★
Part matched perfectly with no installation issues. I’m sure as long as I have equipment I will be back. Thanks
Fit great works like new. Shipping was fine
Guest - July 9, 2020
Verified Purchase
★★★★★
★★★★★
Easy repair
Arrived on time,when you said it would. It matched up perfect, everything is good to go now.
Jimmy - August 31, 2020
Verified Purchase
★★★★★
★★★★★
Identical
Replaced both drag links, parts arrived quickly, fit and work as they should, for a very decent price. Thanks
Guest - September 10, 2022
Verified Purchase
★★★★★
★★★★★
Fixed the problem
yes it was in good condition
Guest - May 16, 2023
Verified Purchase
★★★★★
★★★★★
Great service
The part wad easy to install went well
Guest - July 13, 2023
Verified Purchase
★★★★★
★★★★★
Part worked perfect
Correct part, etc. Would be nice when it replaces a previous version, recommend the new updated parts. For this piece, you need the updated nut fastener (older model is threaded different).
I use this site because they are one of the few with clear diagrams of the equipment I'm working on
Benjamin - September 26, 2023
Verified Purchase
< Prev
1
2
Next >
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Using a socket and a wrench removed the drag links and installed the replacement drag links.Need to save the nuts because the replacement drag links do not come with nuts.
Disconnected the broken part & replaced with new part. Replaced both right & left draglinks even though only one was broken... They were pretty tight but finally got them off.
Remove the nut and washer from the LH spindle assembly and the left nut and washer from the left side of the sector plate gear. Reverse order to assemble the new drag link. Save the nuts and washers, they are not included with the part.
Did you find this story helpful?
Thank you for voting!
Steering drag linkage bars were worn and loose. Needed to be replaced.
1) Using a standard floor hoist (jack), raise the front end of riding mower high enough to allow room for socket wrench to remove linkage nuts.
2) Using socket wrench and open end wrench; loosen and remove old linkage nuts and old lock washers. Tap on old drag linkage bar with rubber hammer and remove bar.
3) Insert new drag l
... Read moreinkage bar.
4) Place new lock washers and finger tighten nuts on both ends of new linkage bar. Using socket wrench and open end wrench, tighten both nuts securely.
5) Lower front end of riding mower using the floor hoist (jack).
It was pretty simple. The dragon link arms only had 1 nut on either end but the trickiest part was to make sure you did not damage the rubber axle cover in the center of the wheel. I had to pry it from the back side to keep from damaging it then to put it back on I had to heated up so it would stretch and then snap back in to place, then
... Read more form back to the washer. This is important to keep dirt dust and some water out of the grease around the axle.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP16382661
Manufacturer Part Number: 597047802
Lawn Mower
- Husqvarna Lawn Mower Model 240472 Parts
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
