OEM DeWALT Electric Drill Parts & Accessories

$5.95

Manufacturer Part Number:: N089668

Genuine Dewalt replacement part, this item is sold individually. The N089668 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly.

Clutch Assembly

★★★★★

(2)

$59.45

Manufacturer Part Number:: 429634-00

This is an authentic manufacturer approved replacement part designed for use with drills/screwdrivers. This clutch assembly is connected to the transmission and the shaft. Keeping an eye on equipment performance will determine when the clutch requires replacement. Includes part numbers 176842-00, 89210-00

Carbon Brush

★★★★★

(5)

$7.16

Manufacturer Part Number:: 176846-04

This carbon brush is an authentic DeWalt replacement part. It is sold individually, 2 are needed to make a set • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that c...

Compression Spring

★★★★★

(7)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: N019351

This is an OEM authorized part. It is sold individually. This spring maintains pressure on the N078437 Sleeve, and the rest of the bit holder assembly, to keep the bit in the holder. If this part fails the bit cannot be held in the bit holder. It is commonly used in impact drivers, and is compatible with the impact drivers listed below.

Carbon Brush With Spring

★★★★★

(10)

$11.43

Manufacturer Part Number:: 450374-12

Genuine OEM replacement This brush is sold individually, 2 are needed for most every electric power tool It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the...

Hog Ring

★★★★★

(6)

$5.95

Manufacturer Part Number:: N053863

This is an authentic OEM replacement part, sold individually. The Hog Ring holds the bit holder assembly together, it is inserted in the very front of the sleeve. Without it the complete bit holder assembly would completely fall apart. Screwdriver is needed for repair. Compatible with the impact drivers listed below.

Power Cord

★★★★★

(75)

$26.47

Manufacturer Part Number:: 330072-98

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also rou...

Ball Bearing

★★★★★

(9)

$22.60

Manufacturer Part Number:: 605040-20

This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bear...

Spring

★★★★★

(5)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: N437890

This is a spring designed to fit within the bit holder assembly of an impact driver, also known as an impact wrench. Positioned between the anvil and ring gear, this spring is accompanied by a washer and hog ring on each side to provide tension and maintain consistent pressure on the inserted bit within the holder. As a high-wear component, this spring will eventually wear out, resulting in a less...

Carbon Brush With Lead

★★★★★

(5)

$9.63

Manufacturer Part Number:: 655213-02

Genuine DeWalt replacement part rnIncludes 1 Carbon Brush with wire lead in rubber sheath attached.rn • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. • Because carbon brushes are wear it...

Plain Washer

★★★★★

(4)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: N016823

This is a genuine OEM part sourced from the manufacturer. Sold individually. Washer provides a bearing surface for fastener load distribution or acts as a spacer. Is used in a number of impact drivers, listed below.

Housing Assembly

★★★★★

(10)

$23.28

Manufacturer Part Number:: N413423

This OEM housing assembly in your impact driver is the protective outer casing that encloses the internal components of the tool, providing structural support. The assembly consists of both the top and bottom sides and it operates using a 20-volt battery. To identify if the housing assembly is broken, look for visible cracks, fractures, or loose components. Excessive vibration or unusual noises du...

DeWALT Electric Drill Parts

Top DeWALT Electric Drill Models

Popular DeWALT Electric Drill Parts

DeWALT Electric Drill Models

Shop by Popular DeWALT Electric Drill Part Types

DeWALT Electric Drill Parts

Search By Model or Part Number

Top DeWALT Electric Drill Models

Popular DeWALT Electric Drill Parts

DeWALT Electric Drill Models

Shop by Popular DeWALT Electric Drill Part Types