Easy
15-30 minutes
This replacement item is used with Dewalt grinders. It is an authentic part supplied directly from original equipment manufacturer. This cord delivers power from the outlet to the tool. If the cord is damaged or torn it is important to replace it immediately and not use the tool until replaced. It is constructed with tough, thick outer rubber insulation for a long service life. Please note the cord protector/grommet is sold separately.
Replacing cord is a simple repair that should only require a screwdriver.
• Remove housing screws
• Separate housing
• Disconnect wires
• Remove old cord
• Secure new cord in place
• Reattach wires
• Reassemble and test the unit
Cord Set (10-ft) 330081-18
OEM part for: DeWALT, Black and Decker
Part Number: 330081-18
$19.33
In Stock
Order within the next 21 minutes and your part ships today! 
Jump To:
Product Description ?
- 10 FT/16-2SJ
- Classification: Part
- Weight: 0.70 lbs.
- Shipping: Ships Worldwide
Frequently Purchased Together ?
Compatibility
This part will fit the following 20 machines
DeWALT
D28065 Type 1 Small Angle Grinder View Diagrams & Manuals
D28065N Type 1 Small Angle Grinder View Diagrams & Manuals
D28115 Type 1 Grinder View Diagrams & Manuals
D28115N Type 1 Grinder View Diagrams & Manuals
D28066N (Type 1) 5in/6in Rattail Sag View Diagrams & Manuals
D28066N (Type 2) 5in/6in Rattail Sag View Diagrams & Manuals
D28116 (Type 1) 115mm Small Angle Grinder View Diagrams & Manuals
D28116 (Type 2) 115mm Small Angle Grinder View Diagrams & Manuals
DWE46066 (Type 1) 6in No Lock Rat Tail View Diagrams & Manuals
DWE43116 (Type 1) 4-1/2-5/6i 13a 9k Tr View Diagrams & Manuals
DWE43113 (Type 1) 4.5-6in 13a Trig Swi View Diagrams & Manuals
D28065 (Type 2) Small Angle Grinder Power Tool View Diagrams & Manuals
D28065N (Type 2) Small Angle Grinder Power Tool View Diagrams & Manuals
D28115 (Type 2) 4-1/2 Small Angle Grinder Power Tool View Diagrams & Manuals
D28115N (Type 2) 4-1/2 Small Angle Grinder Power Tool View Diagrams & Manuals
DWE43113 (Type 2) 4.5-6in 13a Trig Swi Power Tool View Diagrams & Manuals
DWE43116 (Type 2) 4-1/2-5/6i 13a 9k Tr Power Tool View Diagrams & Manuals
DWE43116N (Type 1) 4-1/2 5/6 Tr Gr Grinder Power Tool View Diagrams & Manuals
DWE43116N (Type 2) 4-1/2 5/6 Tr Gr Grinder Power Tool View Diagrams & Manuals
Black and Decker
USALLSAW-QU (Type 1) Motor View Diagrams & Manuals
Show More Compatible Models
This item works with the following types of products:
- Grinder Parts
This part replaces obsolete part #: 330081-19
Repair Videos ?
Watch the Repair Video for
Cord Set (10-ft)
Customer Part Reviews ?
Questions & Answers ?
Our customer Service team is at the ready daily to answer your part and product questions.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Does this fit my product?Questions & Answers for Cord Set (10-ft)
No questions have been asked yet
Customer Repair Instructions ?
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Damaged power cord and missing cord protector
David - June 17, 2023
Tool Type
Grinder
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Torx screwdriver
Replaced power cord and cord protector, no big deal.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Broken power cord
Scott - April 28, 2017
Tool Type
Grinder
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
1. Removed cover.
2. Disconnected power cord from inside connections.
3. Installed new cord, connected to connectors.
4. Reinstalled cover.
5. Test drove!
2. Disconnected power cord from inside connections.
3. Installed new cord, connected to connectors.
4. Reinstalled cover.
5. Test drove!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Would not turn on
Jerry - March 12, 2016
Tool Type
Grinder
Difficulty
Easy
Time
Less than 15 minutes
Tools Used
Screwdriver
Parts Used
I have a short cord that I saved from my other grinders, note: (I have 8 grinders) I am a structural welder. I removed the back half of the grinder and visually checked the brushes, they looked fine. I removed the cord and put on the short cord with out putting it together and plugged it in and it worked fine so I ordered 2 cords one for a pair..
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Grinder would not operate.
Peter - March 7, 2016
Tool Type
Grinder
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Torx bits
Grinder needed new brushes and the cord was damaged. Safety first, Put on eye protection. Cord was easily replaced by removing side cover and removing two screws holding cord wires to switch. Install cord protector on cord. Replace screws with new cord wires in place, reassemble cover. Brushes were also an easy remove and replace. Removed brush covers by removing screw and opening cover. Pull back brush holder spring and lock on pin. Install new brushes by installing brush wire thru hole in brush holder and set brushes in holder and release brush holder spring from pin. Spring rest against brush holder, keeping tension between brushes and against armature. Plug brush wire into brush wire connector. Repeat for other side.Reinstall brush covers install screws to hold cover in place. Test Grinder for correct operation.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Accidentally cut cord
James - September 24, 2018
👍 0 of 1 people found this instruction helpful
Tool Type
Grinder
Difficulty
Easy
Time
15-30 minutes
Tools Used
Screwdriver, Pliers, Torx driver
Parts Used
Handle needed to split in half to remove cord. Needed special torx driver to remove screws a flat bladed screw driver could also used. Two wire cord was removed and new cord was installed Wires on replacement cord were as with different lengths so they could only be installed one way. The Dewalt grinder is well designed for repair services
Did you find this story helpful?
Thanks for voting and helping fellow customers!
OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.
Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.
Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.
Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.
All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.
This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.
