eReplacementParts.com
877-346-4814
Porter Cable Parts
Repair Parts Home  Power Tool Parts  Porter Cable Parts  1313113 Carbon Brush

Carbon Brush 1313113

OEM part for: Porter Cable, Delta

Part Number: 1313113


Install
Videos!
Carbon Brush - 1313113:Porter Cable 360 View
Carbon Brush - 1313113:Porter CableCarbon Brush - 1313113:Porter CableCarbon Brush - 1313113:Porter Cable 360 View
In Stock
Order within the next 5 hours and your part ships today!
Easy 15-30 minutes (44 rated repairs)?
OEM: Original Equipment Manufacturer ?
Porter CableDelta
Does this d-block d-md-none fit my product?

Product Description ?

Genuine OEM replacement part
This brush is sold individually, 2 are needed for the tools shown below
It is always best to replace both brushes, even if only one is worn.

Worn brushes frequently are the cause behind a motor running poorly.
Replacing brushes can fix a motor that’s operating intermittently.
New brushes can restore a motor’s electric braking.

Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

  • Classification: Part
  • Weight: 0.01 lbs.
  • Also Known As: Motor Brush
  • Shipping: Ships Worldwide

Frequently Purchased Together ?

Compatibility

This part will fit the following 23 machines

Porter Cable

1400 Type 1 14 inch Abrasive Cut Off Machine View Diagrams & Manuals
1400 Type 2 14 inch Abrasive Cut Off Machine View Diagrams & Manuals
1400 Type 3 14 inch Abrasive Cut Off Machine View Diagrams & Manuals
PC305TP Type 1 12 inch Planer View Diagrams & Manuals

Delta

22-540 Type 1 12 inch Planer View Diagrams & Manuals
22-540 Type 2 Planer View Diagrams & Manuals
22-560 Type 1 Planer View Diagrams & Manuals
22-560 Type 2 Planer View Diagrams & Manuals
22-565 Type 1 Planer View Diagrams & Manuals
22-580 Type 1 Planer View Diagrams & Manuals
20-150 Type 1 Cut Off Saw View Diagrams & Manuals
TS300 Type 1 Bench Table Saw View Diagrams & Manuals
34-670 Type 1 10 Inch Table Saw View Diagrams & Manuals
34-670 Type 2 10 Inch Table Saw View Diagrams & Manuals
TP305 12-1/2" Portable Planer View Diagrams & Manuals
34-080 Type 1 10" Miter Saw View Diagrams & Manuals
34-080 Type 2 10" Miter Saw View Diagrams & Manuals
36-600 Type 1 Table Saw View Diagrams & Manuals
36-600 Type 2 Table Saw View Diagrams & Manuals
36-610 Type 2 Table Saw View Diagrams & Manuals
36-610 Type 1 Table Saw View Diagrams & Manuals
TP400LS Type 1 12-1/2" Planer View Diagrams & Manuals
TP300 Type 1 Planer View Diagrams & Manuals
Show More Compatible Models
Don't see yours? Try searching our site for :

This item works with the following types of products:

  • Chop Saw Parts
  • Saw Parts
  • Planer Parts
  • Table Saw Parts
  • Miter Saw Parts

Repair Videos ?

Watch the Repair Video for Carbon Brush

Customer Part Reviews ?

4.7
Average Rating (out of 5):
23 Reviews
Click to filter by ratings:
5 stars
20
4 stars
1
3 stars
1
2 stars
1
1 stars
0
  • Highest Rating
  • Most Recent
< PREV
  • 1
  • 2
  • 3
NEXT >
  • Easy repair
    Part arrived quickly. This was for an older tool, so I was happy to find the part still was available.
    Guest - June 20, 2023 Verified Purchase
    Worked as expected.
    Thanks for the parts I needed.
    Guest - March 14, 2023 Verified Purchase
    Quick, easy, and accurate
    The ordering system is easy and the service is quick and accurate
    Guest - March 10, 2023 Verified Purchase
    part was new and shipping was as I reqested.
    The part was directed to a business doing my repair. It was delivered as requested and my saw was fixed. Thank you
    Guest - July 22, 2022 Verified Purchase
    Carbon Brush
    Have not received the brushes to this date, and have no luck with tracing the shipment any help would be appreciated. Hans Hageeier
    iGlobal - January 29, 2022 Verified Purchase
    Easy repair
    The carbon brush fit my planner perfectly. The motor runs smooth and quiet again.
    alan - July 17, 2021 Verified Purchase
    It was what I needed and they had it.
    Fast service and I’m back in business.
    Guest - July 17, 2021 Verified Purchase
    Just like new
    Part arrived when it was expected. Fixed my saw and now it runs like new again.
    Guest - July 9, 2021 Verified Purchase
    no problem
    all good
    Guest - April 5, 2021 Verified Purchase
    Easy repair
    arrived in great time - fit perfectly - happy!!!
    Guest - November 30, 2020 Verified Purchase
    t
    t
    t - t days ago Verified Purchase
    eReplacementParts Team
    t

    Questions & Answers ?

    Our customer Service team is at the ready daily to answer your part and product questions.

    photo of team member
    Ask our Team

    We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

    Does this fit my product?

    Questions & Answers for Carbon Brush


    No questions have been asked yet

    Customer Repair Instructions ?

    All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.

    Easy 15-30 minutes (44 rated repairs)?

    Slow motor speed, sparking

    Charles - October 11, 2018
    👍 6 of 6 people found this instruction helpful
    Tool Type

    Table Saw

    Difficulty

    Easy

    Time

    30-60 minutes

    Tools Used

    Screwdriver

    1) Unplug saw (very important)
    2) Remove plate
    3) Remove blade
    4) Unscrew the upper brush cap (you may need to lower the motor slightly if you have larger hands)
    5) Remove old brush
    6) Use compressed air to clean brush contact area
    7) Insert new brush
    8) Screw on brush cap while compressing brush spring with other hand (the most difficult part of the process)
    9) From under the saw, do the same procedure (4-8) on the lower brush

    Note: You do not have to invert the saw and remove the base, like some videos show (although this might make it easier for people who cannot lie on their backs).

    The old brushes were about half the length of the new ones. The failure appears to be from the lack of spring pressure when they are shorter, not the lack of brush material. Also the buildup of sawdust on the armature can reduce the contact area. If you need to use the saw while waiting for new brushes, you may be able to get more life from the old ones by just removing them and cleaning the contact area with compressed air.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Motor spun, but blade didnt.

    Tony - March 30, 2016
    👍 5 of 5 people found this instruction helpful
    Tool Type

    Table Saw

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver

    I removed the black pulley cover from the end of the motor and replaced the drive belt, then replaced the pulley cover. On the opposite side of the motor I removed the brush caps with a screwdriver, then removed the worn brushes and installed the new ones and replaced the brush caps. The motor runs like new now.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Bad bushes, lots of Sparks & Motor would not turn off

    byron - May 26, 2016
    👍 4 of 4 people found this instruction helpful
    Tool Type

    Table Saw

    Difficulty

    Easy

    Time

    30-60 minutes

    Tools Used

    Screwdriver

    Removed the brush caps with a screwdriver, removed the worn brushes, placed the new brushes in the brush holders and screwed the brush caps back on. Removed the old switch and changed the wires on the back of it one at a time. Then pressed the new switch back in the housing.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Worn out brushes

    don - May 13, 2016
    👍 3 of 3 people found this instruction helpful
    Tool Type

    Table Saw

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver

    Remove the brush caps, then the worn brushes, installed the new brushes and screwed the brush caps back in
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Needed new brushes in motor

    Randy - July 22, 2018
    👍 2 of 2 people found this instruction helpful
    Tool Type

    Chop Saw

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver

    Removed the brush caps with a screwdriver, then removed the old brushes. Installed the new brushes, then replaced the brush caps.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Motor brushes worn out.

    Steve - June 5, 2018
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Table Saw

    Difficulty

    Medium

    Time

    15-30 minutes

    Tools Used

    Screwdriver, Wrench Set

    Remove blade and turn tables saw upside down, on floor, to be able to access motor brush on one side of motor. Remove cap covering brush with straight slot screwdriver. Replace brush and cap and upright tablesaw. Lower the motor, as you would lower the blade, untill you can reach the reverse side of the motor for the other brush. Remove cap with short stub straight slot screwdriver because of limited room for your hands, and replace brush. Reinstall with new brush and replace cap. Reinstall blade.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Motor blew breaker

    vaughn - April 27, 2018
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Table Saw

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver

    Unscrew caps and remove old brushes , keep in mind to see the orientation of the brushes.
    replace cap snug.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Table saw motor losing power and spearking.

    JOHN - April 17, 2018
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Table Saw

    Difficulty

    Easy

    Time

    Less than 15 minutes

    Tools Used

    Screwdriver

    Took out the old brushes and replaced. Motor working perfectly again.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Brushes wore out

    Marvin - April 6, 2018
    👍 1 of 1 people found this instruction helpful
    Tool Type

    Table Saw

    Difficulty

    Medium

    Time

    15-30 minutes

    Tools Used

    Screwdriver, Wrench Set

    Removed motor, removed the brush caps, removed the brushes
    Installed the new brushes and brush caps, installed motor
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    Armature shorted out

    MICHAEL - May 4, 2018
    Tool Type

    Table Saw

    Difficulty

    Medium

    Time

    30-60 minutes

    Tools Used

    Screwdriver, Wrench Set, Hammer and pully puller

    1. Removed the motor
    2. Disassembled the motor
    3. Installed new parts
    4. Reassembled and reinstalled the motor
    5. Repair complete
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!

    OEM stands for Original Equipment Manufacturer and means the part you’re buying is sourced directly from the manufacturer who made your product. At eReplacementParts, we sell only genuine OEM parts, guaranteeing the part you’re purchasing is of better design and of higher quality than aftermarket parts.

    Our product descriptions are a combination of data sourced directly from the manufacturers who made your product as well as content researched and curated by our content & customer service teams. This content is edited and reviewed internally before being made public to customers.

    Our customer service team are at the ready daily to answer your part and product questions. We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.

    All our part reviews are solicited directly from other customers who have purchased this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

    All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part. While we moderate these reviews for profanity, offensive language or personally identifiable information, these reviews are posted exactly as submitted and no alterations are made by our team.

    Based on data from past customer purchasing behaviors, these parts are most commonly purchased together along with the part you are viewing. These parts may be necessary or helpful to replace to complete your current repair.

    All our installation videos are created and produced in collaboration with our in-house repair technician, Mark Sodja, who has helped millions of eReplacementParts customers over the last 13 years repair their products. Mark has years of experience in selling and repairing both commercial and residential products with a specialty in gas-powered equipment.

    This data is collected from customers who submitted a repair instruction after replacing this exact part. Customers can rate how easy the repair was to complete and how long it took. We aggregate this data to provide a repair rating that allows customers to quickly determine the difficulty and time needed to perform their own repair.

    eReplacementParts.com
    7174 South 400 West
    Suite 5
    Midvale, UT 84047
    visa mastercard discover american express PayPal