Throat Plate Assembly 089290001700
Part Number: 089290001700
Leaves our warehouse within
7 - 12 business days
7 - 12 business days
Product Information
Description:
| This is an authentic OEM part that has been sourced to be used with table saws from Ridgid. The plastic throat plate attaches to the table in the area around the blade. This item is used to support material at the cut to aid in making clean cuts and limit splintering. This item is available as an individual replacement part. |
Frequently Purchased With
Compatibility
Products Compatibility
This item works with the following types of products:
- • Saw
- • Table Saw
Questions & Answers for Throat Plate Assembly
Does this part fit a ridgid R4514 10" saw
Ronald
for model number R4514
asked on 2022-11-24
Hello Ronald, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is Part Number: 080035003096. Thank you for your inquiry, good luck with this repair!
eReplacementParts Team November 24, 2022
Do you have a throat plate insert for my table saw
Harry
for model number TS3650
asked on 2022-09-13
Hi Harry,
Thank you for your question. The part number listed under your model number for the dado throat plate is AC1040. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
eReplacementParts Team September 13, 2022
Repair Instructions: Submitted by Customers Like You
14 of 16 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
, Cut Plywood and use glue & \\\'filler material\\\'.
My original throat plate was fine, but I made a ZERO CLEARANCE throat plate from the new throat plate.
1) Cut a piece of 1/8 inch thick plywood to fit over the clearance hole from the bottom side of the throat plate opening with about one inch on either side of the opening for the blade.
2) Be sure not to interfere with the RIVING Knife operation. Use an appropriate GLUE/EPOXY to secure it place. Be sure properly prepare the bottom surface to allow for proper adhesion.
3) After the GLUE/EPOXY dries, fill in the 'opening at the hole' with AUTO BODY filler [or similar material] to make the top surface flat and flush to surface to the original top.
4) After everything is dry and ready to 'raise the blade', CLAMP/SECURE a board over the throat plate and slowly raise the blade through the closed over opening to create the ZERO CLEARANCE opening for your blade.
***Read up and research on making ZERO CLEARANCE throat plates before you start!! ***
2) Be sure not to interfere with the RIVING Knife operation. Use an appropriate GLUE/EPOXY to secure it place. Be sure properly prepare the bottom surface to allow for proper adhesion.
3) After the GLUE/EPOXY dries, fill in the 'opening at the hole' with AUTO BODY filler [or similar material] to make the top surface flat and flush to surface to the original top.
4) After everything is dry and ready to 'raise the blade', CLAMP/SECURE a board over the throat plate and slowly raise the blade through the closed over opening to create the ZERO CLEARANCE opening for your blade.
***Read up and research on making ZERO CLEARANCE throat plates before you start!! ***
Did you find this story helpful?
Thanks for voting and helping fellow customers!
5 of 6 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
, My Table Saw [R4513]; Contact cement and 1/8 \\
I am making ZERO Clearance Insert Plates for my DIFFERENT saw blades used.
1) Cut the 1/8th " plywood to size and shape to provide necessary clearances on the underside of the plate to allow the plate to be installed back into the saw opening. Be sure to make the width wide enough to overlap the blade opening on the plate, but do not allow this piece to interfere with the location of the RIVING KNIFE fit when installed back into the saw. 2) Now cut another piece of 1/8th " plywood to be the exact width of the actual plate opening. be sure the width is an exact fit to fill the opening [again being careful not to interfere with the RIVING KNIFE position). 3)Place the first piece of 1/8th " Plyw under the plate opening in position under the opening. Then place the PLATE on the first piece to confirm that you have NO INTERFERENCE to reinstall the throat plate back into the saw. Temporarily tape the pieces together and 'MARK' the location for a final fit later. 4) Once the top surfaces are FLUSH you can glue the pieces in place with Contact Cement**...first the under side piece of plywood to the plate and then the second piece into the opening from the top surface. [** follow the instructions for the Contact Cement application to the surfaces.]
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
old plate was bent
removed the 5 screws that attach it to the saw and replaced it ;
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, None
Plate went bye bye.
Used fingers to install.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
30-60 minutes
Tools Used:
Screwdriver, Adjustable Wrench
Parts broke and missing
Removed one piece that was messed up, then installed all the new parts, installed as the parts diagram showed, that I looked up on the net.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
, Epoxy for the magnet... No tools required
The original throat plate popped out and got caught in the saw blade damaging it
Replaced missing magnet that holds the throat plate in place... Epoxied the missing magnet in place and slid the throat plate back in... No tools required, Fits perfect as expected. So glad I was able to purchase the original replacement part. Thanks!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Throat plate
Took the old one off and put on the new one.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Lost throtle plate.
Simple repair 4 screws.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Wrench Set
This was just put parts back on that were missing when I purchased this used table saw.
Installed the missing parts.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Table Saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
I screwed up the throat plate while cutting wood.
1. Set the saw upright
2. Ensured that the blade was lowered
3. Removed the damaged throat plate with my fingers
4. Installed a new throat plate with my fingers
5. The plate needed no adjustment, so I was done
6. Folded the saw back up
2. Ensured that the blade was lowered
3. Removed the damaged throat plate with my fingers
4. Installed a new throat plate with my fingers
5. The plate needed no adjustment, so I was done
6. Folded the saw back up
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
6 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
5
4 stars
0
3 stars
0
2 stars
0
1 stars
1
< PREV
- 1
Exactly what I needed in a timely manner
Fit perfectly
Guest -
July 11, 2023
Verified Purchase
Replacement part
It went very well ,and very easy to but what I needed
Guest -
December 7, 2021
Verified Purchase
My go to place for parts
Parts arrive quickly. Are packaged well, no damage.
Dennis -
June 3, 2021
Verified Purchase
Speedy delivery
Gladly surprise for the speedy delivery of the part.
Guest -
April 6, 2021
Verified Purchase
Got perfectly
It was a perfect fit and was shipped fast.
Guest -
September 17, 2020
Verified Purchase
Not even close
The thickness and length of this Ridgid table saw throat plate did not match my R4514 saw. Even if the dimensions matched, it did not have adjustment screws for leveling.
JOSEPH -
June 9, 2022
Verified Purchase
eReplacementParts Team
Thank you for your review. I?m sorry to hear that happened, we will be in touch soon to help fix this issue.
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information
