Product Information
Description:
Genuine manufacturer sourced replacement part used on a Bosch Jig Saws. Switches are a commonly replaced part in power tools, handling on/off operations. Because switches use mechanical internals, they will tend to wear out over time, eventually requiring replacement. It has a plastic body and it is sold individually. To replace this switch you would need a Screwdriver. • First make sure the tools is not plugged in • Then you want to remove screws used to hold two pieces of housing set together • Disconnect wires from the old switch and remove it from the housing • Place the new switch in the housing and connect wires to it • Reassemble the housing |
Frequently Purchased With
Products Compatibility
This item works with the following types of products:
- • Jig saw
- • Saw
Questions & Answers for Switch
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
Tool Type:
Jig saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Didn't turn off
1. Loosen housing screws and remove the housing half
2. Note the wire positions or take a picture
3. Unplug cable from speed controller
4. Remove four power wires from old switch
5. Insert power wires in new switch
6. Plug cable into speed controller
7. Check that the wires are in the correct places and won't be pinched
8. Replace housing half and tighten screws
2. Note the wire positions or take a picture
3. Unplug cable from speed controller
4. Remove four power wires from old switch
5. Insert power wires in new switch
6. Plug cable into speed controller
7. Check that the wires are in the correct places and won't be pinched
8. Replace housing half and tighten screws
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Jig saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
Jigsaw wouldnt turn OFF
opened the jigsaw
made a video of the wiring routing
removed old switch
installed new switch
closed up the tool
made a video of the wiring routing
removed old switch
installed new switch
closed up the tool
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Jig saw
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Jigsaw would not turn on.
Already had pulled out old switch and took pictures with my IPhone for wires. Got new switch and brushes and popped them right in and works like new again!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Jig saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Bad trigger on Bosch jig saw
Remove the screws from the housing.
Remove the wires from the old trigger and reinstall the wires in the same location on the new trigger at the same time so you put them in the correct slots. Two of the wire are a little difficult to remove, I put a very small screw driver in the slots to loosen the connectors up as I pulled on them.
Put new trigger in old trigger location and reinstall housing.
Good to go!
Remove the wires from the old trigger and reinstall the wires in the same location on the new trigger at the same time so you put them in the correct slots. Two of the wire are a little difficult to remove, I put a very small screw driver in the slots to loosen the connectors up as I pulled on them.
Put new trigger in old trigger location and reinstall housing.
Good to go!
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Jig saw
Parts Used:
Repair Difficulty:
Medium
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Pliers
Switch was bad
Separated the housings
Made a wiring diagram
Disconnected the old switch
Connected the new switch
Put the housing back together
Made a wiring diagram
Disconnected the old switch
Connected the new switch
Put the housing back together
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Jig saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver
switch stayed on all the time
Removed screws and one half of the housing.
Made a wiring diagram.
Loosened the cord clamp.
Remove the cord wires.
Then the other wires just like on the wiring diagram.
Tightened up the cord clamp.
Screwed the housings together.
Made a wiring diagram.
Loosened the cord clamp.
Remove the cord wires.
Then the other wires just like on the wiring diagram.
Tightened up the cord clamp.
Screwed the housings together.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Jig saw
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, A torx screwdriver
Switch was staying on
Made sure the jigsaw was not plugged in. Took the screws out of the handle , disconnected the wires to the old switch , then installed the new switch . Then put the handle back on. Works like a charm.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Reviews
5 Reviews
Average Rating (out of 5):
Click to filter by ratings:
5 stars
5
4 stars
0
3 stars
0
2 stars
0
1 stars
0
< PREV
- 1
Easy repair
Working good
Guest -
March 23, 2023
Verified Purchase
Switch for jigsaw!
Got part in 2 days fit perfect great service
robert -
June 7, 2022
Verified Purchase
switch replacement
the switch replacement took about 15 minutes, it works great, thanks
Guest -
February 12, 2022
Verified Purchase
Bosch jigsaw repair
Jigsaw would not shut off, new switch solved the problem!
Roger -
October 12, 2019
Verified Purchase
Identical part, easy repair, it worked perfectly.
Arrived quickly, easy install and works like original. Thanks.
Guest -
July 29, 2019
Verified Purchase
Verified Purchase
eReplacementParts Team
< PREV
- 1
Product Information