Product Information
Description:
This is a Genuine Manufacturer Approved replacement part designed for some Milwaukee Power Tools. This item is sold individually. Due to the use or other factors a cord can crack or get damaged otherwise. It is important to replace a damaged cord before continuing to use a Power Tool. Please note Cord Protector/Sleeve is Sold Separately. |
Frequently Purchased With
Compatibility
the 12 compatible machines
This part is compatible with the following machines:
Milwaukee
6146-30 (D02A) 4.5" Compact Angle Grinder
6117-30 (C91A) 5" HP Angle Grinder With Paddle Switch
6117-31 (C92A) 5" HP Angle Grinder With Paddle Switch
6117-33 (C94A) 5" HP Angle Grinder With Slide Switch
6117-33D (C95A) 5" HP Angle Grinder With Slide Switch
6146-31 (D03A) 4.5" Compact Angle Grinder With Paddle Switch
6117-30 (C91A) 5" HP Angle Grinder With Paddle Switch
6117-31 (C92A) 5" HP Angle Grinder With Paddle Switch
6117-33 (C94A) 5" HP Angle Grinder With Slide Switch
6117-33D (C95A) 5" HP Angle Grinder With Slide Switch
6146-31 (D03A) 4.5" Compact Angle Grinder With Paddle Switch
6146-33 (D04A) 4.5" Compact Angle Grinder With Slide Switch
6147-30 (D05A) 4.5" Compact Angle Grinder With Paddle Switch
6147-31 (D06A) 4.5" Compact Angle Grinder With Paddle Switch
6161-30 (D07A) 6" HP Angle Grinder With Paddle Switch
6161-31 (D08A) 6" HP Angle Grinder With Paddle Switch
6161-33 (D09A) 6" HP Angle Grinder With Slide Switch
6147-30 (D05A) 4.5" Compact Angle Grinder With Paddle Switch
6147-31 (D06A) 4.5" Compact Angle Grinder With Paddle Switch
6161-30 (D07A) 6" HP Angle Grinder With Paddle Switch
6161-31 (D08A) 6" HP Angle Grinder With Paddle Switch
6161-33 (D09A) 6" HP Angle Grinder With Slide Switch
Products Compatibility
This item works with the following types of products:
- • Grinder
Questions & Answers for Power Cord
No questions have been asked yet
Repair Instructions: Submitted by Customers Like You
Tool Type:
Grinder
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Power cord had cut in it.
Removed the rear housing and noted where all of the parts were located. Disconnected the cord from the switch .Slid the cord protector on the new cord. Connected the new cord to the switch. Made sure all the parts were in their place and screwed the housing together.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver, Torx
Worn out pads on palm sanders, bad cords on angle grinders
Took screws out of sander pads and replaced. Removed cut cords from angle grinders installed new cords with protectors.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
Tool Type:
Grinder
Repair Difficulty:
Easy
Time Spent Repairing:
15-30 minutes
Tools Used:
Screwdriver, Torx T-20 bit
Needed a new cord and relief
Remove the rear housing of the grinder. And make a wiring diagram and take a few picture of where the parts inside are located, especially the springs. Remove the cord from the switch. Slide the new cord relief onto the new cord. If want to use terminals on the cord you can get those locally, the cord does not come with them. Attach the cord the the switch. Make sure all of the parts are in the correct place, then put the rear housing back on.
Did you find this story helpful?
Thanks for voting and helping fellow customers!
0 of 1 people found this instruction helpful
Tool Type:
Grinder
Parts Used:
Repair Difficulty:
Easy
Time Spent Repairing:
Less than 15 minutes
Tools Used:
Screwdriver
Cut cord to grinder
Removed the old cord and replaced.
Did you find this story helpful?
Thanks for voting and helping fellow customers!