eReplacementParts.com
866-322-9842
Porter Cable Parts

Power Cord

Part Number: 879182
Porter CableDeWALTBlack and Decker
Availability: 25+ in stock
Price: $14.62
Quantity:
Order within the next 2 hours
and your part ships today!
Product Information
Manufacturer: Porter Cable, DeWALT, Black and Decker
Product Number: 879182
Classification: Part
Weight: 0.49 lbs.
Shipping: Ships Worldwide
Specifications
Length: 7'
Gauge: 18
Wires: 3
Type: Bare Wire
Description:
This cord is a genuine Porter Cable replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life.
Power Cord Specifications:
  • 3 Prongs
  • 3 Wires
  • 18 Gauge
  • 7 Feet Long
  • Porter Cable models: 6302 T4, 6902 T5, T6
  • Products Compatibility

    This item works with the following types of products:

    • • Band Saw
    • • Router
    • • Sander
    • • Saw
    • • Trim Saw
    Questions & Answers

    No questions have been asked yet
    Repair Instructions: Submitted by Customers Like You
    3 of 3 people found this instruction helpful
    Tool Type:
    Sander
    Parts Used:
    Power Cord - 879182
    Sleeve - 838270
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Screwdriver, Wrench Set, Wire stripper
    old power cord was coming apart exposing bare wires
    1. Took top of sander off by removing 4 screws. (Rockwell sander, now Porter-Cable)
    2. Removed old power cord and sleeve by untwisting two wire nuts and unscrewing bolt connecting green ground wire to handle.
    3. Inserted new power cord though sleeve, stripped insulation off end of all three wires.
    4. Connected new power cord to sander using the same two wire nuts, black to black and white to white. Then connect green ground wire to sander handle using same bolt.
    5. Replaced top of sander and tightened it down to secure power cord and sleeve. Works Great!
    ( Make sure sander is unplugged before attempting repair.)
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Sander
    Parts Used:
    Power Cord - 879182
    Sleeve - 838270
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Screwdriver, Pliers
    Sleeve and cord were damaged
    Removed 4 screws cut old wires and attached new cord. Replaced top then replaced 4 screws
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Sander
    Parts Used:
    Power Cord - 879182
    Repair Difficulty:
    Medium
    Time Spent Repairing:
    30-60 minutes
    Tools Used:
    Screwdriver, Pliers, Soldering gun, solder, flux paste, pick (to remove wire from
    Cord got caught in the sander
    Removed half the handle. Removed the switch from the handle. Extracted the wires from the switch and unconnected the ground wire. Cut white wire and trimmed replacement wires from new power cord to length. Tinned the black wire on replacement cord and then reattached cords and handle.

    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Sander
    Parts Used:
    Power Cord - 879182
    Repair Difficulty:
    Medium
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Screwdriver, Pliers
    Cord cut, had to be replaced
    1. Removed handle
    2. Removed old cord
    3. Attached new cord
    4. Replaced handle
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Tool Type:
    Sander
    Parts Used:
    Power Cord - 879182
    Repair Difficulty:
    Easy
    Time Spent Repairing:
    15-30 minutes
    Tools Used:
    Screwdriver
    Broken power cord
    I removed the top half of the motor housing. I disconnected the cord from the tool and made a wiring diagram of where the wires were connected. I took off the cord relief and put on the new cord. Trimmed the wires to the correct length needed. Connected the new cord. Made sure no wires would get pinched when I put the housing back on. Then put the housing back on.
    Did you find this story helpful?
    Thanks for voting and helping fellow customers!
    Discussion
    Discussion for Power Cord - ( 879182 )
    Discussion is closed. To ask our experts a question about a part, use the Q&A feature.
    Reviews
    4.5
    Average Rating (out of 5):
    2 Reviews
    Click to filter by ratings:
    5 stars
    1
    4 stars
    1
    3 stars
    0
    2 stars
    0
    1 stars
    0
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
  • A GoTo place for hard tomfind parts
    Thanks for being a great source for keeping my “antique tools” in good,safe working order!
    Guest - 13 days ago Verified Purchase
    Parts fit and I have had no problem with sander. Delivery was very quick.
    Parts fit and I have had no problem with sander. Delivery was very quick.
    Guest - 13 days ago Verified Purchase
    Verified Purchase
    eReplacementParts Team
    • Highest Rating
    • Most Recent
    < PREV
    • 1
    NEXT >
    Product Information
    Manufacturer: Porter Cable, DeWALT, Black and Decker
    Product Number: 879182
    Classification: Part
    Weight: 0.49 lbs.
    Shipping: Ships Worldwide
    Repair Guides
    Articles:
    Replacing Bad, Cut, or Damaged Power Cords on Your Power Tools
    This article contains tips and basic steps for replacing power cords for most types of power tools, machines, and other ...
    September 18, 2009
    How to Replace the Power Cord on a Porter Cable Belt Sander Model 352VS
    Step-by-step instructions show you how to restore power to your Porter Cable belt sander....
    February 06, 2015
    Related Products
    eReplacementParts.com
    7036 South High Tech Dr.
    Midvale, UT 84047
    visa mastercard discover american express PayPal

    fancyboxy