This is a genuine OEM sourced part is specially designed for Murray snowthrowers. It attaches inside the worm gear bracket and moves the chute when the handle is rotated. Over time it may wear out and begin to fail eventually requiring a replacement. Make sure to refer to the owner's manual and the appropriate diagrams for your model to ensure the correct repair procedure. Note, this high-quality gear-worm is made of durable metal and is sold as an individual component. A wrench set will be needed to perform the replacement.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Great Customer Support
This was an order for 2 items with one being on extended "back order". A quick call to Customer Support confirmed the order status being held up for the backordered item. They quickly split the order with the Chute Worm Gear arriving in a couple days. Support like this will have me coming back, without hesitate, for other parts as needed.
Guest - April 5, 2023
Verified Purchase
★★★★★
★★★★★
Everything was perfect
It all fit
Guest - December 29, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
replace all the parts and turn the monster loose on large amounts of snow in Minnesota to watch it fly far, far away..... thanks for having what I need to keep my snow eating machine growling in the face of Minnesota Winters like
Did you find this story helpful?
Thank you for voting!
The outer retaining had some missing teeth, I ordered any parts in the affected area.
1. Removed the 4 bolts holding the chute housing
2. Removed the worm gear bracket
3. Removed 4 nuts and bolts from the retaining ring holder
4. Removed the tiny cotter pin for the worm gear
5. reassembled all the parts.
Note: The only damage I could see were the broken teeth on the outer ring. I would have b
... Read moreeen very angry if I didn\'t order the worm gear bracket. The damage to the worm gear bracket was only found when it was disassembled.
Read less
Did you find this story helpful?
Thank you for voting!
Chute outer retainer ring was worn and the chute would not rotate 180 degrees with the handle.
1. Remove the chute bolts and the chute.
2. Lift out the inner retainer ring.
3. Remove the 4 bolts that hold the chute mounting flange.(this was the hardest part of the repair, because the heads of the bolt are partly covered.
4. Remove the outer retainer ring and flange plate.
5. exchange the chute worm gears
... Read more />6. Set the new outer retainer ring and place the chute flange inside the retainer ring.
7. Install all 4 bolts then tighten all 4 bolts
8. install the inner retainer ring.
9. Align the bolt holes, making sure the outer retainer is in the proper position to rotate 180 degrees.
10. start the 4 bolts through the inner and outer retainers, with the bolt at the back and front of the chute are all the way through, but the 2 side bolts are flush with the outside of the outer retainer ring.
11. install the chute and start the nut on the front and back bolts. then push the side bolts through and install the nuts.
12. Tighten the nuts but do not over tighten them.
1. Remove the cotter pin at the worm gear joint, pull all the connecting pins and disconnect the assembly.
2. Save all the parts in a small bowl, as they are easy to lose if you are working outside this time of year.
3. pulled worm gear, and removed the worm gear holder, with 11mm sockets both top and bottom.
4. Noti
... Read moreced worm gear holder cracked at both bolt holes, replaced that unit through Sears Parts a eParts didn\'t show that part available.
5. Fit worm gear into bracket, place bolts with their washer up through holes, put top washer and nut on and tighten.
6. Recommend drive rod is reverse order of disassembly and don\'t forget cotter pin.
Unit back fully functional.
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9035829
Manufacturer Part Number: 585196MA
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Transmission or Clutch","title":"Transmission or Clutch","url":"/parts/lawn-and-garden/snow-blower/transmissions-and-clutches/"},{"position":2,"name":"585196MA","title":"585196MA","url":""}]
(2008)_WW_4.gif "Part Location Diagram of 585196MA Murray Wormgear,chute Rotate")
(2008)_WW_4.gif "Part Location Diagram of 585196MA Murray Wormgear,chute Rotate")
