This is a genuine Dewalt replacement part, it is sold individually. The 151442-02 is part of the brake system for the Random Orbit Sanders listed below. They connect to the 624302-00 Brake to help it keep the sanding pad at a slower orbit so it works properly.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Spot on parts
Actually, I ordered several parts to recondition an older Dewalt random orbital sander. The replacement parts were spot on!
Everything, including the springs, brake, bearing and brushes fit perfectly. Runs like a new sander for less than half the replacement cost of the sander. Oh, did I say, I found the sander in a job site dumpster?
Guest - December 18, 2020
Verified Purchase
★★★★★
★★★★★
Fast shipping ..
Fast shipping arrived as described.
Guest - February 1, 2021
Verified Purchase
★★★★★
★★★★★
My Dewalt orbital 5” sander
Got parts “right then” and again “right then” I repaired my Dewalt 5” orbital sander. So very exited that I got it fixed!! Works like new ! Thanks!!!
Guest - April 1, 2021
Verified Purchase
★★★★★
★★★★★
Spring repair
Part is exactly what I needed. Took 15 minutes to replace
Guest - March 29, 2022
Verified Purchase
★★★★★
★★★★★
Repair orbital sander
Parts worked great
Guest - July 4, 2023
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Unplug sander, remove pad screws, take off pad and remove break. Springs are located on brake. Remove springs and install new ones and if the break pad is worn and speed cannot be controlled, replace break pad and springs. Place new or repaired break assembly on sander, and then Velcro pad and insert the 3 retaining screws. Plug back in a
... Read morend get to work!
after receiving parts installed springs, and brake,which gave me a little problem getting balance just right , put pad on and machine works great,very happy!!!
Remove the top cover of the the sander, then you have access to the switch, remove the old switch cover and put on the new one. The screw the top back on. Then remove the sanding pad by removing three screws, then remove the pad. Take the worn brake off and the worn springs. Put the new springs on the brake and install the brake. Then ins
... Read moretall the sanding pad. Then sand away.
1-removed 3 screws to remove pad
2-removed/replaced brake and springs
3-reinstalled pad and screws
Pretty easy to repair about 15 min and $12.00 parts/shipping verses buying new sander for $80.00
1st time for me to repair my own tools!
Already had the old sander pad, brake retainer and springs removed so all I had to do was to install the new parts. Fitting the new springs (2) to the brake retainer took a few minutes and total time was about 15 minutes. No instructions were necessary, These repair parts kept me from purchasing a new orbital sander which would have c
... Read moreost approximately 2X the cost of repair parts.
Read less
Did you find this story helpful?
Thank you for voting!
New brake with old springs did not slow down orbital sander as it should.
Unscrew pad on orbital sander to expose the brake.
Remove the existing springs from brake by bending them out.
Place new springs so they clip into grooves. Use a flat head screwdriver to make sure the springs are well fastened.
Reattach brake and pad.
Did you find this story helpful?
Thank you for voting!
< Prev
1
2
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP10166512
Manufacturer Part Number: 151442-02
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
✖
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Spring or Shock Absorber","title":"Spring or Shock Absorber","url":"/parts/power-tool/sander-polisher/springs-and-shock-absorbers/"},{"position":2,"name":"151442-02","title":"151442-02","url":""}]
