It is a genuine OEM sourced item that is specially designed for use with Dremel rotary tools. The purpose of a brush holder is to secure a carbon brush around the armature, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. This high-quality item is made of durable materials and is sold individaully, keep in mind the brush itself is sold separately.
Troubleshooting
This part works with the following brands:
Dremel
Bosch
This part works with the following products:
Router
Hammer Drill
★
Customer Part Reviews
?
4.0
Average Rating (out of 5):
★★★★★
★★★★★
(4 Reviews)
Click to filter by ratings:
5 stars
3
4 stars
0
3 stars
0
2 stars
0
1 star
1
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Right part, quick shipping.
Right part, received promptly.
Guest - May 30, 2019
Verified Purchase
★★★★★
★★★★★
Easy repair
I got the brush holder that had a resister on it
Guest - June 19, 2019
Verified Purchase
★★★★★
★★★★★
With OEM parts, you redeem or condemn yourself
There are too few sources to buy electronic parts not made in China which are reasonably priced.
Guest - October 24, 2019
Verified Purchase
★★★★★
★★★★★
DID NOT WORK AS EXPECTED
I took my Dremel 4000 apart and replaced the brush bearing with the one I received from EreplacementParts, put it all back together and my Dremel did not power on like I was expecting it to. I even took it apart again to see if not put is together correctly and tried it again- NOTHING. I think I received a bunk part because that is the only thing that could be wrong with my Dremel. I'm hoping for possibly another replacement brush bearing from these guys or at least a refund...
Will update when (if) I hear back from EreplacementParts...
Jennifer - January 15, 2023
Verified Purchase
January 15, 2023
Hello Jennifer, thank you for your review. We are sorry that there may be an issue with the part. If you want to call in with your model number to speak with an agent, we can assist you in resolving this issue. Have a wonderful day.
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
Replaced old brushes along with
Specifically
1. Remove power cord from wall
2. Unscrewed the two flathead screws securing the brushes inside
3. Pulled brushes from each side
4. Removed the 5 or 6 T15 TORX screws
5. Removed collar on drive shaft and hanging bracket from the rear
6. Took top off a
... Read morend notated which wires went where.
7. Removed the two brush holders and replaced with new ones
8. Reassembled and tested
Read less
Did you find this story helpful?
Thank you for voting!
The unit locked up 10 yrs ago while cutting aluminum
1. Disassembled unit
2. Wire power cord to new switch assembly
3. Attached brush holders to field
4. Attached field to switch
5. Routed wires to specific points so unit will close and run
6. Place all button and lock knobs in place.
7. Reassembled unit
(Pay Close Attention To Where The Wires Are
... Read moreRouted, if they are not just right the outer casing will not close cleanly and the motor will not run)
Read less
Did you find this story helpful?
Thank you for voting!
Brush holder solder joint had broken on the brush holder. Had to take it out and replace it
Took screws out of Dremel housing.
Separated the two sides of the housing.
Unplugged the brush holder from the motor
Plugged news brush holder in and set in correct place.
Put housing back together
Tightened housing screws
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP16865257
Manufacturer Part Number: 2610009853
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
