Reciprocating Saw Parts

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: 44-60-1635

This is a genuine OEM sourced replacement part designed for use with Milwaukee sawzall reciprocating saws. This shoe pin secures the shoe retainer. It is made of metal and it is sold individually. To complete this repair you would need a screwdriver and pliers.

Cord Protector

★★★★★

(8)

$5.95

Manufacturer Part Number:: N918736

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Shoe

★★★★★

(9)

$14.78

Manufacturer Part Number:: 163451-9

Genuine Makita replacement part, this item is sold individually. This Shoe is used to place against the material your are cutting It makes it much easier to make the straight or other cuts you desire. The shoe is also adjustable so you can the set the blade stroke depth of cut that you want.

STRAIN RELIEVER

★★★★★

(26)

$11.60

Manufacturer Part Number:: 901266

This is a genuine Porter Cable replacement part, it is sold individually. A Cord Strain Reliever is used on most all power tools. It purpose is to reduce the bending of the cord as it comes out of the housing, which otherwise would cause the cord to crack and wear.

Power Cord

★★★★★

(75)

$26.47

Manufacturer Part Number:: 330072-98

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also rou...

Shoe Assembly

★★★★★

(5)

$8.17

Manufacturer Part Number:: 45-16-0030

This is a pivot shoe assembly for a milwaukee sawzalls sourced directly from original manufacturer. It provides support for your tool while in operation by acting as a spacer/stop. It also helps to reduce vibration and kickback of the sawzall. It is made out of metal and it is sold individually. To replace it you would need a torx screwdriver. • Remove the screws that secure shoe assembly to t...

Brush Holder Assembly

★★★★★

(3)

$5.95

Manufacturer Part Number:: 22-20-0535

This is a genuine Milwaukee replacement part, it is sold individually. 2 are needed for the tools shown below. It includes the Brush and Brush Holder. It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electri...

Shoe Assembly

★★★★★

(7)

$21.57

Manufacturer Part Number:: 45-16-0645

This is a genuine Milwaukee replacement part. It is sold individually for the Milwaukee Sawzalls listed below. The Shoe Assembly helps guide the blade where you want to cut. It is adjustable by pulling down on the 31-52-0090 Shoe Release Lever, for use of longer or shorter blades. The foot pivots for cutting angles. The saw should not be used without this part or it could damage the saw. Part is e...

Carbon Brush

★★★★★

(19)

$5.95

Manufacturer Part Number:: 22-16-0275

Genuine Milwaukee replacement part Includes 1 Carbon Brush sold individually. Please go to the schematic listings for your tool to find the brush assembly parts compatible with this carbon brush and your tool. This carbon brush will fit a wide variety of Milwaukee tools. • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operatin...

Shoe Release Lever

★★★★★

(4)

$5.95

Manufacturer Part Number:: 31-52-0090

Genuine Milwaukee replacement part, this item is sold individually. The shoe can be adjusted forward or backward to take advantage of the unused portion of the blade or for special jobs requiring low blade clearance. To adjust the shoe, pull out the shoe release lever 1/4 turn. Slide the shoe forward or backward to the desired position. After adjusting the shoe, slowly pull the trigger to be sur...

CARBON BRUSH SET

★★★★★

(6)

$16.60

Manufacturer Part Number:: 2610007957

Carbon Brush Set

★★★★★

(7)

$18.43

Manufacturer Part Number:: CB303

This set of two carbon brushes is a genuine Makita replacement part, packaged in an official Makita retail box. Each brush includes wire leads and attached brush springs, and is designed to restore optimal performance in compatible Makita tools. Carbon brushes are among the most commonly replaced components in power tools, as they gradually wear down through friction and regular use. Worn brushes ...

Popular Reciprocating Saw Brands

Popular Reciprocating Saw Parts

Popular Reciprocating Saw Models

All Reciprocating Saw Brands

Shop by Popular Reciprocating Saw Part Types

Reciprocating Saw Parts

Search By Model or Part Number

Popular Reciprocating Saw Brands

Popular Reciprocating Saw Parts

Popular Reciprocating Saw Models

All Reciprocating Saw Brands

Shop by Popular Reciprocating Saw Part Types