Makita Saw Springs and Shock Absorbers

Genuine Makita replacement part, this item is sold individually. The purpose of the 231806-7 Tension Spring is to raise and lower the telescoping lower guard. When you make a cut the Lower Guard will raise up inside of the upper guard, as you get to the end of your cut the Spring will cause the lower guard to return to it original position. The spring is attached to the Lower Guard and also to the...

Genuine Makita replacement part, this item is sold individually. The purpose of the 231839-2 Tension Spring is to return the Lower guard back to its original position after use. To attach the spring, one end is installed on the Lower Guard and the other end is installed in the Blade Case.

This item has been sourced from the original manufacturer to be used with circular saws from Makita. The metal spring is used to provide tension between the lower guard and the blade case. This item allows the guard to pivot through the cut and spring back over the blade after the cut. This item is priced as a single item.

This Torsion spring is a genuine Makita replacement part. It is sold individually.

This part is available individually. The spring washer fits between the wing nut and the flat washer. This washer is small and will need to be replaced if it gets lost or if it breaks. It is made out of metal and no tools should be necessary when replacing this item. This is an OEM Makita part directly sourced from the manufacturer for use with saws, cutters, planers, drills, and trimmers.

This is a Genuine OEM replacement part used on some Makita Power Tools. This is a Metal Spring and it is Sold Individually. Over time springs may loose its tension and may not function as intended. If this part is lost or damaged it must be replaced.

A genuine item that is supplied directly from the original equipment manufacturer for use with Makita miters saws. It is a high-quality replacement for a missing or damaged compression spring that was installed on the new unit, make sure to check appropriate diagrams of your model for the correct location and application of this hardware. Kepe in mind this durable part is made of durable metal and...

This is an OEM part sourced directly from the manufacturer. The compression spring is found in Makita power tools such as plunge routers, chain saws, and circular saws. This part is made of metal, and is generally used to provide tension to components. It may be found in various locations in the machine, depending on model. Please be aware that there are different springs used in the machine. ...

This compression spring is a genuine OEM replacement component designed to maintain proper tension and support smooth internal operation across a variety of power tools. Made from durable spring steel, it helps ensure consistent movement within mechanisms such as levers, guides, or trigger systems, contributing to stable performance and reliable tool function. Replacing a worn or weakened spring h...

The torsion spring attaches to the front arm. This part is available individually and is made out of metal. A screwdriver may be needed when replacing this part which will need to be replaced if it breaks. This is a genuine replacement part sourced from the original manufacturer for use with Makita miter saws.

This is a genuine Makita replacement part that has been sourced from the original manufacturer to be used with miter saws. The metal torsion spring fits between the rear guard and the blade case. The metal spring is used to keep the guard in position and to return the spring when after the guard pivots. This item is sold individually.

This is a genuine OEM Makita replacement part manufactured for use with miter saws. This metal coil spring fits onto the lock pin, and is held under the lock pin cap 10. This spring is sold individually, please see model diagram for any additional parts.

This is an Genuine OEM replacement Compression Spring used on Makita Reciprocating Saws. It is sold individually. This is the Spring that Pushes Shoulder Pin 5 within the Driving Guide Sleeve. Please refer to diagram when ordering parts.

This is a genuine manufacturer-sourced replacement part which is specially designed for Makita compound miter saws. The purpose of this torsion spring is to apply tension on the guard allowing it to retract. If the hardware is worn or damaged, this will provide an identical replacement for the original component that was installed on a new unit. Refer to the appropriate diagrams for your model to ...

This compression spring is a genuine Makita replacement part. It is sold individually.

The compression spring connects to the pin. It is made of metal and is sold individually. This is an OEM part sourced directly from the manufacturer and used in Makita saws. A set of pliers might be necessary during the installation of this item. This part will need to be replaced if it breaks or bends.

The compression spring is made of metal and fits between the stopper and the adjuster. The part is sold individually and is an original Makita part for use in nailers and saws. This is a small part and will need to be replaced if it becomes lost or broken. A screwdriver may be needed when doing the replacement for this part.