Bostitch Nailer Caps and Lids

This is a Genuine OEM sourced replacement part designed for use with Staplers/Nailers. With this Exhaust Cover you can divert the air in any direction you want. It is made out of Plastic and it is Sold Individually. Please note Flange Nut used to secure the Cover is Sold Separately. To replace this item you would need a Hex Key/Allen Wrench.

Keep your nailer or stapler feeding reliably with this magazine end cap, a durable component that secures the end of the magazine while helping to protect the internal pusher and spring assembly. It plays an important role in maintaining proper fastener alignment and helping prevent debris from entering the magazine, supporting smooth and consistent operation. A cracked or damaged end cap can lead...

This is a genuine Bostitch replacement part. The Safety Pad is attached to end of the safety to prevent the material that it is being used on from getting marred or dented by the safety arm. It is a advisable to have one or two extra pads on hand as they do have a tendency to crack and deteriorate over time.

This is a manufacturer sourced replacement part designed for use with Bostitch nailer. This is an end cap to which the hose are connected. This tool uses a 1/4" N.P.T. male plug. This cap is made out of metal and it is sold individually.

The metal compression spring is made of metal and goes between the check pawl and the door. This part is available as an individual replacement and is an OEM replacement part from the manufacturer Bostitch for use in nailers. Springs can lose their tension over time and will need to be replaced. A set of pliers and a socket set may be needed when replacing this spring.

This replacement end cap is specially designed for use with Bostitch nailers. It is supplied directly from original equipment manufacturer and it is sold individually. This end cap is helps to provide a seal for the air chamber. It is the part that the pressure hose would connect to. It is made out of metal and it is sold individually. Please note the o-ring is sold separately. Replacing this ite...

This is an authentic Bostitch replacement part that has been sourced from the original manufacturer to be used with pneumatic finishing nailers. The safety cover is used to cover and prevent damage to the driver guide assembly. This item is available as an individual replacement part.

This item has been OEM sourced to ensure a high level of quality. This deflector is intended to be used with pneumatic nailers from Bostitch. This part is used to cover the end or top of the cylinder and is used to deflect the exhaust air. This item is sold as an individual replacement part.

The exhaust cover attaches to the exhaust cover spacer and is made of plastic. This is an OEM from Bostitch for use in nailers. This item is available as an individual replacement part. If it becomes broken it will need to be replaced and may require an allen wrench during the installation.

This replacement end cap is a high quality item that is manufactured for use with Bostitch nailers and staplers. It is the end cap to which the hose are connected. This tool uses a 1/4" N.P.T. male plug. This cap is made from durable metal and it is sold individually.

This is an original replacement part manufactured for use with pneumatic nailers, or staplers. This special end cap is threaded to screw into the base of the handle, and has a threaded port for the air fitting to connect. The end cap is sealed with an o-ring, it is important to inspect the o-ring for wear, or replace the o-ring to ensure a good seal. The o-ring is available separately, the end cap...

This authentic item is supplied by the original equipment manufacturer for use with Bostitch nailers. It is an identical replacement for a missing or a faulty cap that was installed on a new unit. The part helps to secure the hook, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality cap is ma...

This is an authentic replacement part that has been sourced from the original manufacturer to be used with pneumatic nailers. The cover connects to the exhaust deflector and is used to secure the cover. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

This is a genuine manufacturer-sourced component which is specially designed for use with Bostitch nailers and staplers. It provides an identical replacement for a missing or a faulty end cap that was installed on a new unit. Make sure to check the owner's manual and the appropriate diagrams for your model for the correct location and application of this component. Keep in mind this high-quality e...

This magazine cover is an original part from the Bostitch manufacturer. This part is constructed of high-quality metal, and is compatible with the MIIIFS Stapler. This item is fastened onto the stapler pusher in the magazine assembly, securing the magazine and staples. This part is sold individually. A hex key and a screwdriver may help in the repair.

It is an authentic item that is supplied directly from the original equipment manufacturer for use with Bostitch nailers and staplers. This is an identical replacement for a damaged or a missing frame cap that was installed on a new unit. Refer to the owner's manual and the appropriate diagrams for your model to ensure the exact location and the correct application of this component. Keep in mind ...

This is a genuine Bostitch replacement part that is intended to be used with pneumatic nailers. The durable plastic frame cap attaches to the overmold frame. This item is used as the end cap that covers the top of the cylinder and exhaust valve. The frame cap is sold as an individual replacement part.