OEM Milwaukee Demolition Hammer Parts & Accessories

Brush Service Kit – Part Number: 22-18-6025

$13.14

Manufacturer Part Number:: 22-18-6025

This is a genuine brush set designed for use with Milwaukee rotary hammers. This assembly includes two (2) carbon brushes with lead wires attached. Please note brush holders are sold separately. Due to prolonged contact with an armature brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. To complete this repair you would need a s...

Snap Ring

★★★★★

(1)

$6.53

Manufacturer Part Number:: 34-60-1400

Genuine Milwaukee replacement part, this item is sold individually. This Snap Ring is used in a number of Milwaukee Tools as shown below. Snap Rings are used in various parts of tools. They are usually installed on a shaft to keep a bearing or a gear from moving. They are also used in other applications depending on what tool you are working on. This is an example of an external Snap Ring.

Dust Cap

★★★★★

(1)

$6.28

Manufacturer Part Number:: 42-52-5262

This is an authentic Milwaukee replacement part manufactured for use with rotary hammers. The special dust cap is used to prevent debris from entering the sleeve. This dust cap is available as an individual replacement part, please see model diagram for associative parts.

7mm Ball

★★★★★

(3)

$6.37

Manufacturer Part Number:: 02-02-0275

This is a genuine Milwaukee part that has been sourced from the original manufacturer to ensure a high level of quality. The steel ball is used to reduce friction between the gear case assembly. This item is sold as an individual replacement part.

C-ring

$6.16

Manufacturer Part Number:: 44-90-0014

This c-ring is supplied directly from the original equipment manufacturer. The metal ring is compatible with the Milwaukee 1" D-Handle Rotary Hammer. This protective part is fitted between the chuck sleeve and the ball plate. Although the c-ring is sold individually, two are needed for the hammer. A screwdriver is needed for the replacement.

Chuck Sleeve

★★★★★

(1)

$6.20

Manufacturer Part Number:: 31-58-0037

This authentic item is supplied by the original equipment manufacturer for use with Milwaukee D-handle hammers. It is an identical replacement for a missing or a damaged chuck sleeve that was installed on a new unit. The sleeve is secured over the chuck to protect it. Check the owner's manual and the appropriate diagrams for your model for the exact location and the correct application of this com...

120v Carbon Brush

★★★★★

(4)

$6.16

Manufacturer Part Number:: 22-18-0032

This 120v carbon brush is an OEM direct from the Milwaukee manufacturer. Compatible with the 5262-21 (G43B) 1" SDS D-Handle Hammer, the brush is secured to the brush holder and armature. The purpose of brushes is to conduct current in an electric motor that powers the tool. This part is sold individually. A screwdriver is needed to make the proper removal and replacement.

Switch

★★★★★

(25)

$27.01

Manufacturer Part Number:: 23-66-0177

This Trigger switch has 4 internal terminals. This authentic Milwaukee replacement part is sold individually. rnrnSwitches are commonly replaced parts in power tools. A switch handles all on/off and variable speed functions. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because switches use mechanical internals, they tend to degrade and wear out ov...

Ball Bearing

★★★★★

(1)

$11.09

Manufacturer Part Number:: 02-04-0845

This is a Genuine OEM Approved replacement part used on a variety of Milwaukee Power Tools. This Ball Bearing has multiple applications based on your tool. Ball Bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows ...

Collet

★★★★★

(10)

$8.99

Manufacturer Part Number:: 42-77-0400

This is a genuine Milwaukee Collet for using bits with 1/8-inch arbors. Due to prolonged, heavy use a collet may need to be replaced. Use Collet Nut Wrench Part Number: 45-96-0400 to remove the Collet Nut Part #: 44-40-0770.

Cord Protector

★★★★★

(6)

$6.55

Manufacturer Part Number:: 44-76-0210

This cord protector is a genuine Milwaukee replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

Cord Set

★★★★★

(3)

$31.06

Manufacturer Part Number:: 22-64-0121

This cord is a genuine Milwaukee replacement part and is sold individually. This cord is used on the Milwaukee tool listed below It is a 3 wire cord with 3 prongs and does need to be grounded to the tool.

Milwaukee Demolition Hammer Parts

Top Milwaukee Demolition Hammer Models

Popular Milwaukee Demolition Hammer Parts

Milwaukee Demolition Hammer Models

Shop by Popular Milwaukee Demolition Hammer Part Types

Milwaukee Demolition Hammer Parts

Search By Model or Part Number

Top Milwaukee Demolition Hammer Models

Popular Milwaukee Demolition Hammer Parts

Milwaukee Demolition Hammer Models

Shop by Popular Milwaukee Demolition Hammer Part Types