OEM Craftsman Hammer Drill Parts & Accessories

$25.06

Manufacturer Part Number:: 330072-98

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also rou...

Retaining Ring

★★★★★

(4)

$6.16

Manufacturer Part Number:: 144803-00

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with circular saws and hammer drills. The special retaining ring is commonly used to secure the fan to the armature's shaft. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

Electric Drill Cord Protector

$11.22

Manufacturer Part Number:: 330005-01

This genuine cord protector, also known as a strain relief boot, is designed to safeguard the power cord where it enters your tool housing. Made from flexible, durable material, it helps prevent the cord from bending, twisting, or fraying during regular use, supporting safe and reliable performance. Small but essential, this component is an effective replacement if the original protector is worn o...

Keyless Chuck

★★★★★

(8)

$53.94

Manufacturer Part Number:: N196034

This genuine replacement keyless drill chuck is designed for quick, tool-free bit changes and reliable performance during demanding drilling and driving tasks. Built with a durable metal construction and an automatic locking mechanism, it provides a strong grip to help minimize bit slippage, even in high-torque applications. The chuck supports a wide range of bit sizes and installs directly onto t...

Brush

★★★★★

(2)

$7.25

Manufacturer Part Number:: 176949-17

This is an OEM Manufacturer Sourced replacement part used on certain Hammer Drills. Includes One (1) Carbon Brush with wire lead attached. Please note: this brush is sold individually and most tools would use Two of these carbon brushes. It is always best to replace both brushes, even if only one is worn. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbo...

Shoulder Bolt

★★★★★

(1)

$12.04

Manufacturer Part Number:: 46210

This replacement shoulder bolt is supplied from original equipment manufacturer for use with Ridgid pipe and bolt threading machines. It is used to secure the lever arm assembly to the carriage unit. It is a hex head bolt and it is sold individually. You would need a wrench to install it.

Chuck Key

$6.07

Manufacturer Part Number:: 330034-02

This replacement chuck key is an authentic manufacturer sourced part that is specially produced for use with Dewalt and Black and Decker drills. The chuck key is designed to allow the user to tighten and loosen the jaws of a drill chuck. It is made of durable, high quality metal and it is sold individually.

Detent Spring

★★★★★

(1)

$5.95

Minimum Quantity of 2 required

Manufacturer Part Number:: N014681

Depth Gauge

$6.16

Manufacturer Part Number:: 940357-00

This genuine manufacturer-supplied part is sourced from the original manufacturer to be used with DeWALT and Black and Decker hammer drills. The metal depth gauge connects to the auxiliary handle and is used to indicate the depth of the hole created by the drill. It is sold as an individual item. Replacing it is a simple task that does not require any special tools. Check the owner's manual for yo...

Bearing Ball 626z Od19xid6x6

★★★★★

(2)

$6.55

Manufacturer Part Number:: 681761001

This genuine OEM sourced replacement ball bearing is a standard item which has multiple uses on a variety of power tools. Please check diagrams for proper application of this item. The bearing is specially designed to reduce friction between rotating parts. Over time it will wear out, at this point it should be replaced. This is a sealed metal bearing and it is sold individually.

BRUSH

$6.55

Manufacturer Part Number:: 90545899

Detent

$6.16

Manufacturer Part Number:: 326467-00

This authentic item is supplied directly from the original equipment manufacturer for use with electric power tools. A detent is a device used to mechanically resist or arrest the rotation of a wheel, axle, or spindle. It is a special hardware which may have multiple applications, please make sure to check the appropriate diagrams of your model for the correct location and application of this dete...

Craftsman Hammer Drill Parts

Top Craftsman Hammer Drill Models

Popular Craftsman Hammer Drill Parts

Craftsman Hammer Drill Models

Craftsman Hammer Drill Parts

Search By Model or Part Number

Top Craftsman Hammer Drill Models

Popular Craftsman Hammer Drill Parts

Craftsman Hammer Drill Models