DeWALT Angle Grinder Power Cords

This is an original replacement part manufactured for use with DeWalt angle grinders. This two wire cord had a rubberized jacket, and the wires have crimped terminals to make installation easier. The cordset is available individually.

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the new cord wires to go correctly into wire terminals also rou...

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

This replacement item is used with Dewalt grinders. It is an authentic part supplied directly from original equipment manufacturer. This cord delivers power from the outlet to the tool. If the cord is damaged or torn it is important to replace it immediately and not use the tool until replaced. It is constructed with tough, thick outer rubber insulation for a long service life. Please note the cor...

This is a Genuine OEM replacement Protector Grommet which is used on some Dewalt Angle Sanders. This part is made out of Rubber and is Sold Individually. It is important to have a cord protector on your tool to improve friction, seal cable and protect it from a potential damage.

This genuine cord protector, also known as a strain relief boot, is designed to safeguard the power cord where it enters your tool housing. Made from flexible, durable material, it helps prevent the cord from bending, twisting, or fraying during regular use, supporting safe and reliable performance. Small but essential, this component is an effective replacement if the original protector is worn o...

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 18 Gauge • 10 Feet Long

This is a Genuine OEM Dewalt replacement part used on several Dewalt Grinders. This Cord is sold individually and it does NOT include Cord Protector Part Number: 330005-01 which can be ordered separately. If the cord is damaged or torn it is important to replace it immediately and not use the tool because this can cause a serious damage or injury.

This cord protector is a genuine Dewalt replacement part. It is specially produced for use with angle grinders. It slides onto the power cord and fits securely at the end. The firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. It is made out of rubber and it is sold individually.

This replacement power cordset is designed to provide safe and reliable electrical power delivery to compatible corded power tools. Constructed with durable, heavy-duty insulation and flexible cord materials, it helps withstand demanding jobsite conditions while maintaining consistent power flow to the motor and internal electronics. Ideal for replacing a damaged, worn, or malfunctioning power cor...

This is a manufacturer sourced replacement part commonly used on Dewalt angle grinders. It helps to supply electricity needed for the tool. If the cord is damaged it is important to replace it before continuing to use the tool. Please note cord protector/sleeve is sold separately. To complete this repair you would need a screwdriver. • Remove housing screws • Separate housing pieces • Di...

This is a genuine manufacturer-sourced component which is specially designed for use with DeWALT angle grinders. The power cord is hardwired to the tool in order to supply power from a standard U.S. outlet. If the cord is damaged it is important to replace it before continuing to use the tool. It provides an identical replacement for a missing or a faulty component that was installed on a new unit...

This is an authentic part that is supplied directly from the original equipment manufacturer for DeWALT circular saws. The cord protector is used to protect the power cord from getting damaged. To install the cord protector, simply push the power cord in place through the cord protector. This part is made of rubber and is sold individually.

This is an authentic manufacturer made replacement part which is specially designed for use with Dewalt and Black and Decker die grinders. The power cord connect to the switch and brings power to the unit. This part is made of flexible plastic and is sold individually. The power cord protector is sold separately. You will need a screwdriver, crimping pliers, and a pair of needle nose pliers to aid you in this repair.

This is a genuine part which is supplied directly by the original equipment manufacturer and is used with Porter Cable, Black and Decker, and Dewalt impact wrenches and drywall screwdrivers. When plugged into the wall, the power cord transfers power to the unit. This part is made of flexible plastic and metal, it is also sold individually. For installation, you will need a screwdriver to remove an...