Screwdriver Parts
We sell only genuine OEM parts.
OR
Popular Screwdriver Brands
See All
Popular Screwdriver Parts
- Manufacturer Part Number:
- 96558-00
This is the clutch • for various models of screw guns and drywall screwdrivers. Screw guns, not to be confused with power drills, feature a nose instead of a chuck and the clutch within is responsible for engaging or disengaging the motor of the screw gun to stop it from overdriving the screw. This OEM clutch is made of durable metal, has a 1-inch diameter and includes only a single retaining ring...
- Manufacturer Part Number:
- 429634-00
This is an authentic manufacturer approved replacement part designed for use with drills/screwdrivers. This clutch assembly is connected to the transmission and the shaft. Keeping an eye on equipment performance will determine when the clutch requires replacement. Includes part numbers 176842-00, 89210-00
- Manufacturer Part Number:
- 3600703011
- Manufacturer Part Number:
- 696631-00
Genuine Dewalt replacement part, this item is sold individually. The 696631-00 Steel Ball is part of the chuck assembly of the Impact Drivers shown below. When you pull back the sleeve of the chuck assembly and insert your bit, the Steel Ball is the part that locks the bit in the chuck assembly. In the Screw Drivers listed below this is the part that secures the Bit Holder in the spindle.
- Manufacturer Part Number:
- CB407
This set includes 2 Carbon Brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes frequently are the cause behind a motor running poorly. • Replacing brushes can fix a motor that's operating intermittently. • New b...
- Manufacturer Part Number:
- 90593303-01
This is a genuine Black and Decker replacement charger, sold individually. It’s designed to recharge the battery used in the cordless tools listed below. Over time, chargers can wear out or stop functioning properly. Replacing the charger is a cost-effective solution that can extend the life of your tools—often much less expensive than purchasing a brand-new unit.
- Manufacturer Part Number:
- 605040-20
This Ball Bearing has metal shielding on both sides. This is a genuine Dewalt replacement part that is sold individually. • Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. • Bear...
- Manufacturer Part Number:
- 2600703013
- Manufacturer Part Number:
- CB408
This #191938-1 (CB-408) Makita carbon brush set contains two individual carbon brushes with wire leads and brush springs attached. The set contains genuine Makita replacement parts, and comes packaged in a Makita retail box. This brush set will fit the Makita tools listed at the bottom of the page. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an...
- Manufacturer Part Number:
- 176846-04
This carbon brush is an authentic DeWalt replacement part. It is sold individually, 2 are needed to make a set • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. The reason is that c...
- Manufacturer Part Number:
- CB440
The brush box kit fits a variety of cordless gardening tools. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder. Due to friction, carbon brushes are common replacement parts. If the functioning of your motor changes and does not work, then check if the brush is worn out or inspect the wire lead for cracks, burns and other damage. Replacing the b...
- Manufacturer Part Number:
- N918736
This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.
Popular Screwdriver Models
-
DeWALT DW284 (Type 4)
-
DeWALT DCF630B (Type 1)
-
DeWALT DW255 (Type 6)
-
DeWALT DCF610S2 (Type 3)
-
DeWALT DCF610S2 (Type 2)
-
Skil 289
-
Black and Decker BDCSFL20C (Type 2)
-
Senco DS275 (18V2P0001N)
-
Skil 281
-
DeWALT DW257 (Type 5)
-
DeWALT DW257 (Type 6)
-
Porter Cable 54502 (Type-1)
-
DeWALT DCF620B (Type 1)
-
Bosch 2475 ((TYPE 1)(F012247502))
-
DeWALT DWHT66719 (Type 1)
-
DeWALT DW267 (Type 4)
