Genuine Manufacturer Sourced replacement part used on a variety of Power Tools. This part is made out of Metal and it is sold individually. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Easy Fix
Came quickly and was exact match
Guest - November 12, 2019
Verified Purchase
★★★★★
★★★★★
Table saw parts
Great service
Guest - November 12, 2019
Verified Purchase
★★★★★
★★★★★
=ƒæì
=ƒæì
David - December 7, 2019
Verified Purchase
★★★★★
★★★★★
great part
exact fit great customer service fast shipping I will be doing more business in the future
Guest - July 15, 2020
Verified Purchase
★★★★★
★★★★★
Easy to replace the bearing
It is very smooth to fix my tables which is 20 years old. I did change the bearings twice. My tablesaw is my priority.
Guest - January 14, 2021
Verified Purchase
★★★★★
★★★★★
worked!
The schematics of the table saw helped to determine the defective part.
Very helpful.
Guest - August 7, 2021
Verified Purchase
★★★★★
★★★★★
Worked as expected and fit perfectly
My table saw is working like new again. Thanks
Juan - August 17, 2021
Verified Purchase
★★★★★
★★★★★
The exact part
Thanks for the quick service and ease of finding the part I needed. This is the second time I've ordered from ereplacement parts. So glad I found this site.
Guest - March 8, 2022
Verified Purchase
★★★★★
★★★★★
Notsohappy
The bearings l purchased were fine...however, on 12/16/19 l ordered some additional pieces, and added expedited shipping...still have not seen anything after a week and a half...consequently l have not been able to complete the projects, costing me time and money...please tell me your next step
Guest - December 26, 2019
Verified Purchase
Questions & Answers
?
Our customer Service team is at the ready daily to answer your part and product questions.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Ask our Team
We have a dedicated staff with decades of collective experience in helping customers just like you purchase parts to repair their products.
This was about a 2-3 hour process. Could have been less if I had jigs to removing and setting the bearings already, but I had to cobble together a setup using scrap wood and metal.
1. Unplugged the tool!
2. Removed the blade
3. Loosened the belt tension. Loosened two bolts that secured motor on pivot and lifted up
... Read more. Removed belts one at a time (there are 3)
4. Removed spanner nut and arbor nut on the back of the shaft. When doing the arbor nut you need a wrench for the blade-side and a socket for the other side. Remember, the nut is reverse-threaded! Righty-loosey, lefty-tighty in this case.
5. After those are loose, tapped the non-blade side of the shaft with a rubber mallet to extract it.
6. There was one bearing still on the shaft, and one bearing in the assembly. The one of the shaft had to be removed with an arbor press and creativity (it is difficult to get up under the flange, need to use a wrench or couple pieces of steel and bang on those). The bearing that was still in the assembly just comes out, but you may need to tap it from the other side if it\'s stuck.
7. Once bearings are removed (which is the longest part of the process), put the new one on the shaft. When installing the new ones, make sure to only put force against the outer ring/race of the bearing where it is strongest. If you hit the cage/shield, you will mess up the bearings as it is soft metal there. Just be patient and clever.
8. Now the tricky part, reassembling the shaft assembly. Look at the diagram for which parts to put on first.
9. Once all the shaft parts are in place, tighten down the spanner nut to lock the loose bearing in place.
10. CRITICAL: Put arbor nut on, but DO NOT wrench down on it. Just get it to meet up with the end of the thread. Putting any amount of torque on it after it has met a surface will compress the bearings in a direction they are not meant to handle force, shortening the lifespan of the bearings. This is the second time I\'ve reinstalled the bearings in 6 months and talking to an expert convinced me that is the issue we\'ve been having.
The bearings that are installed now are already sounding gritty again, whereas when they were freshly installed they were quiet as a mouse. Take care in reinstalling because it will determine how long your bearings last.
Read less
Did you find this story helpful?
Thank you for voting!
Saw made squealing sound, vibration, and slight wobble in blade initially.
1. Removed rails and extension table.
2. Removed saw table top (as 1 piece). Make note of any shims under the table top when lifting it off.
3. Removed belts by loosening saw motor.
4. Removed arbor assembly as a unit.
5. Replaced both bearings, spacers, and load spring. The arbor shaft has a left hand threaded nu
... Read moret on the end that required cutting off as it was so tight. I would recommend ordering a new nut.
6. Reinstalled arbor assembly. (Turn tilt adjustment wheel to aid in getting assemble aligned properly. Lubricate all parts to ease installation and don\'t try to force any of the mating parts.
7. Reinstall all other parts in reverse order (3-1)
Remove the cutterhead from the jointer. Remove the pulley from the cutterhead by loosening the set screws and pulling on the pulley and removing the shaft key. Use a bearing puller to remove the old bearings. Then use a socket the same size as the inner race of the new bearing to tap the socket with the hammer, to seat the bearing on the
... Read morecutterhead. Then install the pulley and the cutterhead back on the jointer.
Remove cast-iron top, all belts pulleys and anything else in the way. Carefully tap out threaded washer to get to bearing. Then reassemble the same way you took it apart
1. Loosen the motor belt tension
2. unscrew the left loosening nut
3. push the shaft out
4. take the ball bearing out with bearing puller
5. mount the new bearing on
6. add the new side bearing on too
7. screw the nut on tighten by counterclockwise tightening.
Wasted one hour trying to ta
... Read moreke the ball bearing out by simply using two metal plates and a piece of wood an hammering it. Borrowed my brother\'s ball bearing puller and took only 25 minutes to assemble after that.
Removed jointer knife head assembly.
Pressed old bearings from assembly carefully marking right and left bearing mounts before removal.
Pressed new bearings into assembly.
Mounted assembly back into jointer base.
Checked alinement and bold torques.
Made final jointer table alinement adjustments and started j
... Read moreointer.
Read less
Did you find this story helpful?
Thank you for voting!
Ball bearing was wore out within a year
William from NEWTOWN, Connecticut
0 of 1 peoplefound this instruction helpful.
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I try to figure out why ball bearing was wore out within a year after 15 years. So, I did put some lubes around two ball bearing. I might hope these bearings keep longer running.
Did you find this story helpful?
Thank you for voting!
Ball bearing on arbor shaft of my Jet table saw went bad
James from Omaha, Nebraska
0 of 1 peoplefound this instruction helpful.
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Time consuming part of the job was taking apart the saw with extensions on both sides and front, then lifting off the actual top. Fairly straight forward getting the belts off then removing the shaft after that. Took pics to remember how the spacers and washers went, replaced the bearings and proceeded to reassemble. Works great.
Did you find this story helpful?
Thank you for voting!
Worn bearings on upper wheel, caused blade to wobble front to back. Vibration
1. Remove blade
2. Remove wheel
3. Lay on a bench with the open area under center area
4. Using wooden rod, place rod through center of bearing to reach bearing on other side.
5. Tap bearing out evenly around all sides. Use a little harder tap to get started.
6. Flip over wheel and repeat for other bearing.
... Read more Easy once first bearing is out of way.
7. Clean inside surface of wheel prior to inserting new bearings
8. Find small flat piece of wood, 2x4 0r 1x4 then place new bearing over hole. Place wood on top of bearing then tap evenly to get started. Get eye level with wheel and slowly tap in place.
9. Install wheel
10. Install blade
11. Done!!
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
✖
Stock Status
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
_WW_4.gif "Part Location Diagram of BB-6203ZZ Powermatic Ball Bearing")
_WW_4.gif "Part Location Diagram of BB-6203ZZ Powermatic Ball Bearing")
