This thrust washer is an authentic item which is supplied by the original manufacturer for Murray and Snapper lawn mowers. It is a special type of washer that will resist torque applied by the bearing while ensuring a tight fit. Over time it may wear out, get damaged or simply lost eventually requiring a replacement. This thrust washer is made of a durable material and is sold as an individual component. Note, you may need a wrench set to remove and resecure the hardware that holds this part. Check the diagrams of your specific model for the exact location and application.
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Perfect Fit!
Fast delivery and perfect fit. Thank you.
Guest - November 12, 2020
Verified Purchase
★★★★★
★★★★★
probably needed this
This is just a large fiber washer that fits against the friction wheel. The one on the mower seemed not to be very worn, but while in there, I felt good about replacing this inexpensive part.
Larry - December 8, 2020
Verified Purchase
★★★★★
★★★★★
Thrust washer
Exact fit
Guest - April 27, 2021
Verified Purchase
Customer Repair Instructions
All our customer repair instructions are solicited directly from other customers just like you who have purchased and replaced this exact part.
Easy
30 - 60 mins
(6 rated repairs)?
< Prev
1
Next >
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Removed 5 nuts ( used vise grips to hold assembly for nut removal and replacement) did all work with mower sitting on all four wheels. Used flashlight and looked through holes at back of mower. Mowed grass with no slipping of clutch. Mission accomplished!
I have a chain hoist. So I backed my mower up to it and raised it about 2ft. Then used a 1/2\" drive ratchet with 15/16 socket to hold drive wheel in place. Then used a 3/8\" drive ratchet and 1/2\" deep well socket along with a pipe for a cheater bar to break the 4 nuts (they\'re very tight if it\'s never been replaced). Once they\'re lo
... Read moreose they\'ll come off with your fingers. Then just reverse the process. Probably won\'t need the cheater bar to tighten them back. ALSO when installing the thrust washer be sure it\'s turns freely before tightening the cover plate down completely.
Read less
Did you find this story helpful?
Thank you for voting!
Belt was bad, drive disk was bad, yoke was bad and blades were worn out.
Removed the old belt, put the new one on, removed the old yoke, replaced with the new one, then removed the old drive disk, and installer the new one. Last, replaced the old blades with the new ones.
Did you find this story helpful?
Thank you for voting!
Replaced nylon bushing on steering shaft and linkage arms
Stood the snapper RER on end and secured it
Secured the friction ring w/ a pair of vise grips
Using a socket wrench removed the 4 mounting bolts
Slid off the friction ring
Replaced the friction ring and washer, aligning w/ the bolt mounting holes
Secured the friction ring w/ vise grips
Inserted and tigh
... Read moretened the 4 mounting bolts
Read less
Did you find this story helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
ERP Number: ERP9070364
Manufacturer Part Number: 7014523YP
This part is in stock in our warehouse and will ship out within 1 business day of the order being placed.
New stock is on the way! On order parts usually ship within 7 business days.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.
